Search Results

Search Again
Page 1 of 2
  1. Cheesehead
    Post

    Translator/maf Problem

    Thanks for the feedback! I think I'll try a new MAF this time.
    Post by: Cheesehead, Jul 26, 2003 in forum: Computer Chips 101
  2. Cheesehead
    Post

    Translator/maf Problem

    I tried it again today--- Cold-- ignition on, not running maf = 3 started maf jumps to 255 then settles to 6 -...
    Post by: Cheesehead, Jul 26, 2003 in forum: Computer Chips 101
  3. Cheesehead
    Post

    Translator/maf Problem

    Thanks for the suggestions--I'll do some more tests tomorrow. Are there any numbers that I can use to be sure that I have the correct MAF?
    Post by: Cheesehead, Jul 26, 2003 in forum: Computer Chips 101
  4. Cheesehead
    Post

    Translator/maf Problem

    Code 33 -- higher MAF reading than expected. It's supposed to be an Impala SS MAF. I have tried setting the 1st button to both "3" & "0". I...
    Post by: Cheesehead, Jul 23, 2003 in forum: Computer Chips 101
  5. Cheesehead
    Post

    Translator/maf Problem

    I recently purchased a used Translator and a used MAF off from EBAY. I installed both last night and am getting a service engine light. TurboLink...
    Post by: Cheesehead, Jul 22, 2003 in forum: Computer Chips 101
  6. Cheesehead
    Post

    what kind of HP #'s?

    Still haven't finished this setup. I ruptured a disk in my lower back while switching the intake and turbo and haven't been able to lean over the...
    Post by: Cheesehead, Feb 27, 2003 in forum: Hot Air (non-intercooled) Tech
  7. Cheesehead
    Post

    what kind of HP #'s?

    Don't have a part #. I bought it two years ago through Ron's Custom Automotive in NJ. It was $675 plus my old turbo. His phone # is 800-718-7667.
    Post by: Cheesehead, Feb 27, 2003 in forum: Hot Air (non-intercooled) Tech
  8. Cheesehead
    Post

    what kind of HP #'s?

    I have a TA-49 in the hotair housing from Limit Engineering and it was a direct bolt-on. You will need to port the elbow and the turbo to intake...
    Post by: Cheesehead, Feb 27, 2003 in forum: Hot Air (non-intercooled) Tech
  9. Cheesehead
    Post

    Holy crap!!! YEEEEHHAHAAAAAAA!!!!!!

    I'm also interested in PIC's. Send to: mrogers@uwc.edu THANKS!
    Post by: Cheesehead, Oct 13, 2002 in forum: Hot Air (non-intercooled) Tech
  10. Cheesehead
    Post

    Still fuzzy on the ECM converson thing

    Brent, Where are you located in Wisconsin? I have a Casper's UltraChip setup (check out Casper Electronic's website for more details) for the...
    Post by: Cheesehead, Oct 10, 2002 in forum: Hot Air (non-intercooled) Tech
  11. Cheesehead
    Post

    ramchargers dual radiator fan

    Does anyone know if the fit would be the same on an '85--are the radiator dimensions the same? Also, how much power (amps) does this thing...
    Post by: Cheesehead, Jan 15, 2002 in forum: General Turbo Buick Tech
  12. Cheesehead
    Post

    3" Down pipe from ESP

    Does anyone have any experience with this vendor? I need a new hood insulator pad. How about the 3" downpipe? Does it fit? Can they deliver?
    Post by: Cheesehead, Nov 7, 2001 in forum: Hot Air (non-intercooled) Tech
  13. Cheesehead
    Post

    Prototype Turbomotion V3 HOTAIR intake goes 11.91!!

    Any results from the Jay Carter variable timing chip? Has anyone else tried one of these chips on a hotair?
    Post by: Cheesehead, Oct 31, 2001 in forum: Hot Air (non-intercooled) Tech
  14. Cheesehead
    Post

    engine tie down

    Try this site: http://www.users.voicenet.com/~mrrieg/stealth.html
    Post by: Cheesehead, Sep 28, 2001 in forum: Hot Air (non-intercooled) Tech
  15. Cheesehead
    Post

    Bad Maf??

    Mine both started and idled better with the MAF unplugged. It would also start with the bad unit connected. Don't know if there are circumstances...
    Post by: Cheesehead, Sep 24, 2001 in forum: Hot Air (non-intercooled) Tech
  16. Cheesehead
    Post

    Bad Maf??

    I tried the 85 MAF this morning. It ran better with the mismatched 85 MAF and 87 ECM than it has for the last month with the bad Tomco (87) ECM (no...
    Post by: Cheesehead, Sep 23, 2001 in forum: Hot Air (non-intercooled) Tech
  17. Cheesehead
    Post

    Bad Maf??

    Thanks for the reply Slow_85. Will the '85 MAF work well enough with the 87 ECM for a meaningful test, or do I also need to switch the ECM back to...
    Post by: Cheesehead, Sep 22, 2001 in forum: Hot Air (non-intercooled) Tech
  18. Cheesehead
    Post

    Bad Maf??

    About a month ago I converted my 85GN to 87 ECM and switched the MAF to a new Tomco unit from Postons. Haven't been able to get the car to idle and...
    Post by: Cheesehead, Sep 22, 2001 in forum: Hot Air (non-intercooled) Tech
  19. Cheesehead
    Post

    Knock Detector

    Anybody????????????
    Post by: Cheesehead, Sep 4, 2001 in forum: Hot Air (non-intercooled) Tech
  20. Cheesehead
    Post

    Knock Detector

    I just picked up a replacement knock detector for my 85GN. Two dumb questions: Whats the simplest way to get at it? Do I have to remove the...
    Post by: Cheesehead, Sep 2, 2001 in forum: Hot Air (non-intercooled) Tech
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2
^ Top