Search Results

Search Again
Page 1 of 9
  1. GN ERGY
    Post

    Double checking: Front wheel BS 17x7 or 8, 4"BS?

    I don't have any rubbing, but my rear control arms are boxed and have urethane bushings in them, so I don't have hardly any side to side movement....
    Post by: GN ERGY, Jun 26, 2012 in forum: General Turbo Buick Tech
  2. GN ERGY
    Post

    Syclone Ecm for sale

    Sold Tarey
    Post by: GN ERGY, Dec 4, 2009 in forum: Syclone & Typhoon Tech Forum
  3. GN ERGY
    Thread

    Syclone Ecm for sale

    Got it from bruce when I lived in ohio, he was going to show me how to adapt it to run in the GN like he did. $40.00 plus 5 bucks for shipping Tarey
    Thread by: GN ERGY, Dec 2, 2009, 1 replies, in forum: Syclone & Typhoon Tech Forum
  4. GN ERGY
    Post

    Valve Springs???

    I have about 55,000 miles on it. I started it up and it ran ok, but I'm laid off right now so I don't have any $$$ to put insurance on it to drive...
    Post by: GN ERGY, Aug 14, 2009 in forum: Engine Tech
  5. GN ERGY
    Post

    Valve Springs???

    After getting the valve covers off and using some clean rags to block all the holes in the head so you don't loose a keeper down there, I took my...
    Post by: GN ERGY, Aug 13, 2009 in forum: Engine Tech
  6. GN ERGY
    Post

    which engine oil to use...

    I run Mobil 1 5W40 Turbo deisel synthetic. It has 1300 ppm ZDDP. I run Mobil 1 synthetic in everything I own and I didn't notice any extra or more...
    Post by: GN ERGY, Aug 12, 2009 in forum: General Turbo Buick Tech
  7. GN ERGY
    Post

    Best way to pull this bearing from axle?

    Both autozone and checker rent the slide hammer needed to get those out. I just did rear wheel bearings on my 91 burb. Tarey
    Post by: GN ERGY, Aug 11, 2009 in forum: General Turbo Buick Tech
  8. GN ERGY
    Post

    spal fans

    I got my spals from Hartline performance and I think he has the adapter plug too. Tarey
    Post by: GN ERGY, Aug 11, 2009 in forum: General Turbo Buick Tech
  9. GN ERGY
    Post

    Dropping oil pan: neccesary to remove flywheel?

    Just use some pieces of thread and tie the pan gasket to the pan so it doesn't move when you go to put it back together. Then cut them out when you...
    Post by: GN ERGY, Aug 5, 2009 in forum: General Turbo Buick Tech
  10. GN ERGY
    Post

    Pics - GN1's/valve covers with heater box?

    I took the heat shield off and notched it to clear the valve cover. I have the M&A valve covers. Tarey
    Post by: GN ERGY, Aug 2, 2009 in forum: Engine Tech
  11. GN ERGY
    Post

    Car Skid now its Overheting

    I went over to Davids house and we found one of the rear freeze plugs, either the plug itself or right next to it is leaking. The previous owner must...
    Post by: GN ERGY, Aug 1, 2009 in forum: General Turbo Buick Tech
  12. GN ERGY
    Post

    What Brand Of Guages?

    DJ BARRON, that is a great looking dash. If I didn't have the Cyberdyne digital dash, I would build one like yours. Tarey
    Post by: GN ERGY, Jul 31, 2009 in forum: General Turbo Buick Tech
  13. GN ERGY
    Post

    Hose and Clamp Set

    Try this place HoseTechniques Silicone Turbo Hose, Buy Direct from Manufacturer, Best Quality / Best Price - Hose Techniques established 1983 -...
    Post by: GN ERGY, Jul 30, 2009 in forum: General Turbo Buick Tech
  14. GN ERGY
    Post

    Trying to Install Car alarm

    Print it, that's what I did for my alarm. This way you can have it with you while you do the install. Tarey
    Post by: GN ERGY, Jul 29, 2009 in forum: General Turbo Buick Tech
  15. GN ERGY
    Post

    Trying to Pre-Diagnose

    Sounds like old gas and just needs a tune up. Good luck, sounds like a good deal. Tarey
    Post by: GN ERGY, Jul 27, 2009 in forum: General Turbo Buick Tech
  16. GN ERGY
    Post

    Trying to Install Car alarm

    It's 12 volts hot all the time with a 30 amp fuse in line coming from contact 87 of a relay ( probably the relay that cuts out the starter ) Tarey...
    Post by: GN ERGY, Jul 27, 2009 in forum: General Turbo Buick Tech
  17. GN ERGY
    Post

    fan upgrade info

    I went with the Spals and got them from Hartline performance. Tarey
    Post by: GN ERGY, Jul 25, 2009 in forum: General Turbo Buick Tech
  18. GN ERGY
    Post

    What is best cleaner for driveway?

    I just use some gasoline, let it soak a minute and wipe it up. Brake and parts cleaner works good too. Tarey
    Post by: GN ERGY, Jul 19, 2009 in forum: General Turbo Buick Tech
  19. GN ERGY
    Post

    Power Antenna Nylon Cable

    I just did mine the other day. Got the part #19151297 from the local GM dealer, price was $33. I told him come on can't you give me a better price,...
    Post by: GN ERGY, Jul 11, 2009 in forum: General Turbo Buick Tech
  20. GN ERGY
    Post

    Any UFC 100 Predictions??

    I hope Mir beats lesser ( he reminds me of the big bully from school that needs his A$$ kicked.) I'm rootin for GSP also. Tarey
    Post by: GN ERGY, Jul 10, 2009 in forum: Turbo Lounge
Showing results 1 to 20 of 163 Next >
Search Again
Page 1 of 9
^ Top