Recent content by Kovmat

Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!
  1. K

    1947 willys grand national

    SWEET!!!! Its nice to see I am not the only one crazy enough to try this.
  2. K

    AC Line switch question

    Hey all, Need a little help on my Hybrid project. Doing a custom install of an 86 motor and am currently working on getting all the AC lines in place. I am using the original compressor with a Vinatage Air system. My question: There is a pressue switch on the high side of the AC lines...
  3. K

    10 years of collecting parts. Need to fund new toy. no seats lots of parts. What ya need. gn part

    Looking for the AC lines that connect to the compressor for 86. Have those?
  4. K

    Fuse block Schematic for 86/87

    Thanks.
  5. K

    Fuse block Schematic for 86/87

    Wiring my hybrid and need a legible copy of the fuse block schematic. Anyone have one? I also would like the ignition switch schematic as well. Thanks, Matt
  6. K

    VSS signal to ECM

    Thanks for the reply, sounds like you have a pretty good understanding of basic electrionics. I used to dabble in electronics years ago and know just enough to be dangerous. I have one of those autometer Hall Effect senders that puts out 16 pulses per revolution. The plan was to use JK flip...
  7. K

    VSS signal to ECM

    I am finally getting around to wiring my Hybred project. I want to make sure I get the signal right going to the ECM to indicate the veichle speed. I have a mechanical speedometer that is calibrated at 1000 revolutions per mile. If I understand correctly, the signal coming into the ECM is...
  8. K

    Plug Wires

    Exactly what I was looking for. Thanks.
  9. K

    Plug Wires

    I had to move my coil pack to make everything fit in my Hybrid project so the stock length plug wires probably won't work for me. I would like to be able to make them myself to the exact lenght. Any suggestions on what to use and where to get them? Thanks, Matt
  10. K

    Wastegate Wiring?

    Wiring my Hybrid pjt and had a question about the Wastegate Soleniod Wiring. One Wire goes to the ECM, other to the brake SW. My question is: When I hit the brakes what is that wire going to the brake sw looking for? Does it get pulled to Ground or is it looking for 12 vots? Thanks, Matt
  11. K

    safety switch wiring?

    Thanks. What does the ECM do with the signal? Will the ECM prevent the car from starting if it is not grounded? Thanks, Matt
  12. K

    safety switch wiring?

    Doing my Hybrid wiring and have a question about wiring the safety switch. My question has to do with the ECM Pin B10. Can someone tell me what kind of a signal this pin is looking for? Thanks, Matt
  13. K

    Bearing play?

    That is good to know about G-Pop. I have been working with a guy named Jim. He knew right away how to solve the bearing problem so I don't think he is stearing me wrong.
  14. K

    Bearing play?

    AJ, Thanks for the reply. I think it was rebuild a few times, and modified already to use the screws for the thrust bearing. I got my parts from G-pop. I talked to them this morning, they are sending me bearings that are 15 thousands over so I should be able to use the TA 49 housing...
  15. K

    Bearing play?

    I bought a used TA 49 Turbo that needed a re-build. I am in the process of rebuilding it. I was putting it together and it seemed that there was a lot of play between the new bearings and the center housing. So I decided to do a comparison to my stock turbo. I took the stock turbo apart and...
See more

Online statistics

Members online
2
Guests online
13,162
Total visitors
13,164
Totals may include hidden visitors.

Newest members

Stay Connected

Back
Top