You can type here any text you want

Search results

Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!
  1. 0

    Front Spring R&R

    I am replacing the springs on my GN with Moog 5638/5413's. There was a thread here that I looked for but cannot find again asking if the springs can be replaced with the weight of the car and a floor jack, or do I need to use a spring compressor? I am anxious to get this thing sitting level...
  3. 0

    Sunvisor vanity miror fabric

    Has anyone *successfully* found a way to seperate the vanity mirror lid to replace the fabric on the outer side? I had the visors recovered, and have spare material, but understand the plastic was "welded" as opposed to glued, making disassembly difficult, if not impossible, to say the least...
  4. 0

    Front End Rebuild

    My GN has a sagging RF spring, about 1.25 " lower than the LF. The car only has 68k miles, but thought it would be a good time to j replace ball joints, upper/lower control arm bushings, springs and steering components. I figure I have to disassemble to some extent anyway, why not replace 24...
  5. 0

    PowerLogger Basics...

    I purchased a PowerLogger about a year ago, but for a number of reasons, have not had the time to install. Now that I have a garage and some time, I am slowly working the install. I have a basically stock setup, (see sig) and would like to know if I can install without a wideband and EGT...
  6. 0

    Huntsville AL Area Cruise Nights

    I am moving from the northern Virginia area after 38 years to the Huntsville, AL area within the next month and a half. Does anyone know of any cruise nights that way?
  7. 0

    Used Duramax purchase, tips?

    Thinking of purchasing a 05 Chevy Silverado uramax/Allison combo. Not knowing an awful lot (read:little) about diesels, what should I look for? The one I am considering has 72k miles, going to look Saturday. Thanks!
  8. 0

    GMC Denali Pickup

    I am not sure where to post this... I am looking for comments, good and bad and or personal experience with 4 wheel steering on a 2003 GMC Denali Pickup with around 112k miles.I am thinking of buying one, but know little about the system Depending on the feedback or comments, is there anyone in...
  9. 0

    VSS input on ECM

    Just checking... The VSS input can be found on the ECM at pin A10, correct? This is the smaller (24 vs: 32 pin) connector, correct? Thanks!
  10. 0

    Powerlogger installation

    I just purchased a PowerLogger... arer there any tips/suggestions anyone has learned in the installation process? Pretty straight forward, but I thought someone might have a suggestion or two. Thanks!
  11. 0

    For supporting Vendors only?

    Please delete, thanks!
  12. 0

    VDO Tachometer question

    I am building a GNX dash using the VDO Vision series gauges (tach is # 333-155). My first test using Casper's wiring harness, the tach did not function. The tach is wired using the same (white) connector from the former tach/boost wiring harness. Do I need to wire this directly to the unused...
  13. 0

    IP CLuster Removal Tach/Boost Wiring

    I am converting my 87 to a GNX dash and am in the process of removing the stock IP cluster... the only remaining task is to remove the tach/boost wiring. Is this clamped somewhere? I can't "feel" the connection from underneath. Can I tug on the harness some more to bring it to a point I can...
  14. 0

    UnderdogGN Excellent seller!

    After reading all the horror stories of people getting ripped off I am happy to post GOOD WORDS for a change. I was looking for some small pieces of wiring, UnderdogGN had them and said I could have it for the cost of shipping! When it arrived, it was a virtually complete dash harness, of...
  15. 0

    GNX Fender Vents

    I am looking to purchase a set of quality GNX style fender vents. I already have the reproduction under hood ducting, and was looking for recommendations as to vendors... and anyone's opinions, experiences, etc. Thanks!
  16. 0

    PM Problems

    I cannot get to my PM's... I get the message below: Not Found The requested document was not found on this server. Web Server at turbobuick.com Any idea's?
  17. 0

    Junk Dash Harness??

    Does anyone have a chunk (18" or so) of the factory wiring harness that plugs into the standard analog cluster for an 86-87 GN? I am in the process of building a GNX dash and would like to use the factory wiring and color codes on the project. Thanks!
  18. 0

    A/R question

    Just a general question... I have a TE44 and the compressor housing is marked AR .60. Most I have seen or heard about are .63 what is the difference, and what is desireable, or makes it desireable? Always learning here! Thanks
  19. 0

    Pinion Shaft Bolt

    Does anyone know the part number for a 87 GN G80 pinion shaft bolt? Thanks in advance!
  20. 0

    Axle removal

    Does my 87 gn use c-clips to retain the rear axle? I just found an axle seal leaking and will replace both. I am familiar with the older GM 12 bolt units and just want to see if this is similar. thanks!
  21. 0

    Methanol Life

    I have a Razor's kit in my GN. It is infrequently driven, shows, cruzin, fair weather, etc. How long will the meth retain it's "potency" or whatever you would call it? Thanks!

Online statistics

Members online
22
Guests online
14,086
Total visitors
14,108
Totals may include hidden visitors.

Latest posts

Newest members

Stay Connected

Back
Top