Search results

Cleaning out the garage / going a different direction. All prices are OBO and do not include shipping from 77433. I have more pictures of everything, just ask if you need to see something specific. Send a message or call seven 1 three 5 one 6 - five 701. Thanks. HBC Boost controller ($100) Old...

291 4.1 block - standard bore, pulled from a running car - $400 obo .030 JE forged over bore pistons for 4.1 on stock turbo rods - Sold stock heads - ported, big valves, worked well when pulled, one rocker pedestal repaired - $900 obo stock heads, untouched - $250 obo stock 86-87 radiator, needs...

I've been trying to figure this out for a while. I noticed a few weeks ago that under acceleration or high rpms my volts light would flicker off and on a few times. I don't drive my car everyday but I noticed the next few times I drove the car it seemed to get more frequent until I checked my...

I just recently built a new motor and am looking into a fuel system. I'd like to keep things as simple as possible and retain the stock tank as this is a street car. I have a girdled 109 block, champion irons, roller cam/rockers, 67mm turbo and front mount. I think I should be solidly in the...

I've been through a lot of older threads regarding roller cams and I still have questions. I know I am going with a roller cam. The grind I can figure out myself, I believe. However, when picking a roller cam, what determining factors would make me go with a billet over the austemper roller...

What I have: -.030 bare 109 block -.030 forged pistons -484 4.1 block with lots of cracks between the center headbolt holes and the water jackets -nice forged pistons for a 4.1 -stock .020/.020 crank -stock rods -67mm turbo -fmic -champion irons -60# injectors -dual nozzle alky...

I'm going to run a flat tappet cam with about .470-.480 lift. How heavy should my valve springs be?

I got home last night, turn the car (my dad's 85 t-type) and noticed the volt light was on. I turned the car back on and the light went off. i had a long day so i just left it over night. when i checked this morning the light was still on, turned the car on (didn't act like it had a low charge...

I managed to break my turbo bracket. If anyone has a spare, let me know. thx.

The ATS reading on my scanmaster isn't reading. When I switch to read the ATS it shows "- - -" flashing but I'm not getting an SES light of a malfunction code. This just started about a month or two ago which is around the same time i installed my GEN II with plug n play harness. the ATS is the...

I swapped in an intercooled set-up about 3 years ago. since then the fans never have stayed on like they do from the factory with the delay. the cars turns of, the fans turn off. about 3 weeks ago i turned my car off and the fans stayed on. i thought it was weird but wasnt too worried but after...

I'm in need of a racegate shaft. If anyone has a good shaft from a racegate or even some sort of unusable racegate but with a good shaft I am interested. Please email me at cantdrivefiftyfive@yahoo.com Thanks.

I need the buckle end of the seatbelt. I prefer one from a 84 but I can make any of them work.

I might be in need of stock untouched heads. If anyone has a set, let me know. Thanks.

What is the lowest boost level you can tune to. I am looking to run as low as 10 psi on my car at times and am wondering if the 38mm tial wastegate will be large enough. I have a 4.1 with a PT61 if that helps.

I may be looking for a .63 exhaust housing for a PT61 (one from a PT52 or a TA52 will work as they are the same). If you have one please let me know and what your price is. Thanks.

ATR Headers for sale. The passenger side header has an EGT gauge probe. You can leave it in or weld it up. Its just a small hole. Price is $550 shipped for the headers and regular crossover. If you want the crossover with the 2 deltagates it'll be $600 shipped and if you want both it'll be $650...

I have 2 sets of brackets used to convert to the LS1 brake set-up. They are made from 5/16" 1018 low carbon steel. $45 shipped if paying by money order, $48 if paying by paypal.

Has anyone adapted the frame mount in some way to use the standard 2.5" coilover springs?

Did ATR make the external wastegate downpipes for stock and ATR headers or did they make just one version of this pipe? TIA