Search results

So I notice my pinion seal was leaking . I replace the seal and added fluid . Drove around but now it’s leaking again but from the Pinion Bolt area . Should I have added sealer or RTV to the splines of the pinion ?? I read some do add something. Which is better if needed ???

I’m going to be upgrading my 20 year old shocks . What is everyone using ? Coil overs are not in the budget . My car is lowered with Eibach springs and Bilstein shocks . It feels like I don’t have enough shock travel due to the car being lowered . Been like this for years . Want to try...

How long do fuel pump “ Hotwires “ last ? Im asking because I’m have a intermittent start/no start . I see my fp gauge has zero pressure and no sound of the pump priming . I had also used the jumper wire behind the alternator to prime the pump and it would make the car start but not all the...

Looking for some adjustable coil overs

I have a few parts for sale . Had some parts posted some time ago but not sure what happen to it . Anyway , just cleaning stuff from the shed . 1- Used AC Compressor, condenser and Lines pictured. $200 2- Used Stock Intercooler with Shroud. $120 3- Used Stock reman MAF $25 4-...

So I think my Speedo gauge is jacked up. Long sorry short, I was having volt/charging issues a while back . Happen to be a dead volt dash bulb. I had taken the gauge cluster out. Speedo needle had popped out. I thought I had popped it back in. Took car for a drive , it started making noises...

I have a new build with a new rebuild transmission. Still in the break end period. I’m noticing a big thump when it down shifts from 3rd to 2nd. Nothing on upshifting . Feels fine . Didnt do this before I took out the tranny . I lifted the rear end. Put it in neutral and I got this noise ? What...

As title states . Before I order one .

I can’t seem to get fuel pressure when I turn key to ignition on ? When I crank the car to start , then it will pressurize and start the car , idle and run like normal . I’m guessing it’s running off the Oil pressure switch . It’s a new build. I’m in my break-period so just driving around with...

As title says

Have some parts that have been sitting for a good while . Okay condition. A little elbow grease and should clean up good . Stock IC with shroud and mounting plate. $120 plus shipping Also a Stock radiator. Worked when pulled from car 8 years ago . $100 plus shipping And last is AC...

I wanted to set my cam sensor on my engine stand . I have Casper’s tool that I bought over 13 years ago but never used it . I think the battery is dead . Tried to jump another 9v battery but had no luck . LED didn’t light up . Might of messed up the soldering or something pulling on it . So is...

I have an older Kenne Bell fuel pressure regulator I bought when he was still doing Buick stuff. Are these rebuildable? I'm sure they are as it has the small screws I can remove. So my other question is I see KIRBANS has the diaphragm . Will that be the correct one assuming the screw holes line...

Does anyone know if I can get this clip at any parts store ? I attempted to install AN lines this weekend but noticed this one particular fitting at fuel sender unit was kinda loose . I attempted to push it but it’s not tight enough . I can pull it out easily . Or is that the way it is ?

So I’m trying to reinstall the brass oil block back into my engine but it’s clock in the wrong direction? At this point it’s starts to get real snug so I will only will have about 1/4 turn before it’s tight . This is a different 109 block than my original 109 as that one the brass block is...

I'm just about to drop in my NEW Stroker 3.8 with all forged internals. I'm debating if I should go with E85 injectors or gas 80# injectors with my alky kit? This is the last piece to the puzzle! I would like to be at around 500+ rwhp . Looking to get to the 10's if that's possible. I've...

I have a gbody parts 3” DP with welded 02 bung . Good shape. No dents as I could see. Could use a little polish but works flawless . Good fit also . $250 plus ride . I’m in SoCal Thanks

I am wanting to do my own AN Fuel lines to save on cost. Seems pretty easy. Has anyone used ANfittingsdirect. http://www.anfittingsdirect.com/ So my question is are they of good quality? I'm checking if the Teflon has carbon as that is what's required right? Has anyone used this company before?

Looking for a external wastegate or a DP with external WG provision . Just checking here before I buy new .

As title states . Has approximately 5,000 miles it . Was on my weekend car . $300 plus shipping or trades ? Need 80# injectors Downpipe with ext wastegate Or new external wastegate