Search results

  1. Q

    Looking for a good 2004r core

    I'm interested. Can you PM me your phone number do I can talk to you about it?
  2. Q

    Looking for a good 2004r core

    I am. I haven't been actively looking since the car is sitting since all my transmission issues. But yes I still do need one . I have just about every billetpart CK performance makes for a 2004r and I've had the trans apart 3 times now and it still isn't right. This time I want to use a new...
  3. Q

    Looking for a good 2004r core

    Let me see if anyone closer has one 1st. Thank you for the offer. I'll let you know
  4. Q

    Looking for a good 2004r core

    I really just need a good case but a hole core would be fine also. I'm in Lancaster Pa. If there is anyone close with one they don't need please PM me. Thanks
  5. Q

    Entire 3.8 motor

    Could you send me some pictures and where in MD are you? I will also PM you
  6. Q

    under drive crank pulley off my 87 GN $50

    I have no idea what this is worth. It was on my 87 GN when I bought it. It's a steel pulley and I have the belt that was with it. I sand blasted it and was going to powder coat it but I'm never going to use it $50 OBO
  7. Q

    New GNX fender flares aftermarket

    I bought these about 4 years ago and other then taking them out of the box I've never used them. Asking $250 obo
  8. Q

    PTE 5831 turbo almost new $600

    I have a PTE 5831 turbo I bought a few years ago from gbodyparts. I put about 300 miles on it and I blew my motor. Just as a precaution I sent it back to gbodyparts and they went through the hole turbo to make sure it was ok. I haven't installed it since. Asking $600 obo
  9. Q

    What valve springs with 218-212 roller cam

    I did figure out the problem after working on it in 30 minute increments a few times a week for months. It was a silicone intake elbow that connects my air filter that was collapsing over 5000rpm. The strange part its the same intake pipe I've used for years with my old setup. My new 6265 turbo...
  10. Q

    What valve springs with 218-212 roller cam

    Brian, can I give you a call tomorrow to pick your brain on this? I had your number somewhere from the turbo I bought from you last winter.
  11. Q

    What valve springs with 218-212 roller cam

    2 of the 3 I tried came from running stock motors. Although my motor isn't stock anymore. What kind of HP will the stock modules support? I even tested them with a caspers module tester
  12. Q

    What valve springs with 218-212 roller cam

    I've tried 3 different stock ignition/coil assemblies. All had the exact same outcome.
  13. Q

    What valve springs with 218-212 roller cam

    Nope. It's about the exact same. In the 5000-5200 rpm and then it falls on its face. Feels like I took my foot fully off the throttle.
  14. Q

    What valve springs with 218-212 roller cam

    Fuel pressure and AFR seems all good. I have a autometer fuel pressure gauge hooked up and a wide band hooked up. I'm actually running on the rich end at WOT and fuel pressure at the rails never drop
  15. Q

    What valve springs with 218-212 roller cam

    I finally got around to installing PAC 1201 springs. I took it for a test drive and I still have the abrupt loss of boost / power around 5000-5200rpm. Car feels like you took your foot off the gas even though it's still WOT. I've data logged and it looks like the boost starts to drop out 1st but...
  16. Q

    Misc Stock and Performance Parts

    The flange in your 1st picture I will take if no one else is before me. Let me know. Thanks
  17. Q

    What valve springs with 218-212 roller cam

    I finally got around to measuring my installed height and pressure It looks like the installed height is 1.753 at 115lbs. I think that sounds soft. I will order a set of PAC 1201
  18. Q

    What valve springs with 218-212 roller cam

    I finally got around to measuring my installed height and pressure My k-750 springs were installed at 1.753" and with the pressure checker I borrowed that is about 115lbs.
Top