Search results

  1. czimpel

    Tranny Parts !

    That would be awesome, thanks Mike.
  2. czimpel

    Tranny Parts !

    My evaporator core cracked and I can't find a new one anywhere. Does anyone have a good used one they would part with?
  3. czimpel

    T6Pee party thread. (members only).

    T6P has been shut down due to Covid.
  4. czimpel

    Misc. 200-4R Parts and Tools

    I also would be interested in the lot if Scott passes.
  5. czimpel

    Milky oil...trying to find the cause

    Makes sense, but I honestly would rather know that it is sealed up properly without the tabs. I get what you are saying for sure though, probably not the best move, but I like redoing things.:p
  6. czimpel

    What is this part?

    It looks like the heater control tucked down and out of the way. I believe it controls the flow of hot coolant through the heater core.
  7. czimpel

    Milky oil...trying to find the cause

    I'm running the fel pro 1000's and ARP studs. I am going to put a seal tab in there as well, but I wanted to see if I had an issue first.
  8. czimpel

    Milky oil...trying to find the cause

    Disassembled everything and had it checked out. Nothing found. Put it all back together and all is still good(except a couple different issues) with about 50 miles on it. No signs of coolant leaking or milky oil.
  9. czimpel

    Broken Rocker arm and bent pushrod

    Still running correctly after about 25 miles.
  10. czimpel

    Broken Rocker arm and bent pushrod

    No. I put a new rocker and pushrod in and it runs perfect again. Haven't driven it under boost yet, but seems ok at this point. I'm just seeing if anyone has had this happen so I could check for possible issues. Thanks, Cory
  11. czimpel

    Broken Rocker arm and bent pushrod

    I'm on a roller. I tried to look at the cross brace last night, and as far as I can see it is still in place. #5 is hard to see. I can see every other cross brace with ease on that side.
  12. czimpel

    Broken Rocker arm and bent pushrod

    Just pulled the heads to check gaskets. Pulled a couple rods and mains to double check bearing. Other than that it is exactly as before except the pushrods and timing chain set. Same Fel Pro 1000 gaskets. Running ARP head studs, so the head should not be lifting at 20psi.
  13. czimpel

    Broken Rocker arm and bent pushrod

    Morel lifters. Only 20-21 boost. Never had any issues before. The only change I made was replacing the TC set with a T/A billet set. I was on it when it popped.
  14. czimpel

    Broken Rocker arm and bent pushrod

    The rocker does not look hot at all, and they are oiling. It was the exhaust rocker that broke, and it's pushrod is straight. The intake rocker on the same cylinder is fine, but the push is bent.
  15. czimpel

    Broken Rocker arm and bent pushrod

    Budget 4.1 • ATR Billet Roller RP309G • Champion Ported Irons setup with roller springs. It was running good. I pulled the motor due to milky oil, I didn't find any issue visible to me, but this now has just happened with about 20 miles on it after getting it back together.
  16. czimpel

    Broken Rocker arm and bent pushrod

    Was this a fluke, or do I have something messed up? Haven't had this issue before, but just got the motor back together. Can having not enough lifter preload cause this by chance, because I did use shorter pushrods than the previous time to get my preload in check. I'm wondering if I got it...
  17. czimpel

    Temp Sensor -38 on scanmaster correct on PL

    That was it Ronnie, plug was laying in the socket, but never got plugged in all the way. I thought there were only the 2 temp sensors. Learning everyday!
  18. czimpel

    Temp Sensor -38 on scanmaster correct on PL

    Thanks Ronnie, I'll try start there. Where does the powerlogger pull its temp data from?
  19. czimpel

    Temp Sensor -38 on scanmaster correct on PL

    I have an issue where my temp sensor is reading -38 on my scanmaster, but reads correctly on the PowerLogger. Car starts hard when cold, so assuming this is causing the issue. Is this just a bad TS or do I have a wiring issue. Just reinstalled the motor, so wires were being moved around...
Top