Search results

  1. C

    Cherry red header @ #5

    TPS was .52 so I adjusted that back and started it up got it up to temp and it didn't glow. Anyone care to look at the scanmaster log? Thanks, Joe
  2. C

    Cherry red header @ #5

    Quick vid I took after I turned it over.
  3. C

    Cherry red header @ #5

    Thanks for everyone's input, it is beyond appreciated. I'll have some time to check things out tm. I have a scanmaster g and can do a log and post it here. Just to address a few items: - injectors were just cleaned and flowed before install -not getting a ces light -can anyone recomend what...
  4. C

    Cherry red header @ #5

    Just buttoned up and ran the motor after head gasket failed at cylinder 3. Started up fine, chased down a coolant leak at the heater box and then found this... scary.
  5. C

    Accesory bracket confusion

    You're a life saver. Thanks!
  6. C

    Accesory bracket confusion

    I took it all apart and didnt take any pictures! Can someone point me to a good parts diagram that shows me how to get all the accessories back on? Thanks!
  7. C

    Pushrod order

    I had thought so but couldn't possibly leave it to "eyeballin" it. Thanks!
  8. C

    Sensor / plug id

    Any recommendations on where to get the boot?
  9. C

    Pushrod order

    Guys I screwed up the order of the pushrods when removing my drivers side head. What do you recommend I do on reassembly? Thanks Joe
  10. C

    Dyno Tuning near Long Island

    That's a fairly far haul even if i take the ferry. Sent from my SM-N900P using Tapatalk
  11. C

    Dyno Tuning near Long Island

    Im with Joe! Prefferably one who can tune Big stuff 3 and e86. Sent from my SM-N900P using Tapatalk
  12. C

    Sensor / plug id

    Pulled the wiring harness off and this one hiding behind/below the O2 sensor lost/melted it's rubber boot. Sent from my SM-N900P using Tapatalk
  13. C

    Scanmaster G setup with ALDLDroid

    Got my nice new SMG in today and it looks great! I can't understand how the last owner went without a scantool. :facepalm: With that said I'm having trouble getting it to communicate with my phone which was the entire reason for the purchase. See pics attached. Thanks!
  14. C

    UMI sway bar

    I can make an offer on everything. Is this still available?
  15. C

    Anyone been thru this? buying a car from Canada?

    Just did it. I met the seller at the u.s. border. Some paperwork had to be taken care of. Other than that it was stupid easy. Sent from my SM-N900P using Tapatalk
  16. C

    1987 Buick Grand National-lots of mods-$12500

    Getting it across the border was no big deal. Towing the trailer home through the mountains in thunderstorms and downpours was terrible.. icing on the cake was the 1.5 hours of traffic to get through NYC. The seller and his dad were absolutely great! The car is just as described. All parties...
  17. C

    1987 Buick Grand National-lots of mods-$12500

    Bringing her back to her birth country Saturday!
  18. C

    Wtb 87 GN t-top roller/project

    I wound up buying a running car. Thanks!
  19. C

    1987 Buick Grand National-lots of mods-$12500

    Very interested. Text sent!
  20. C

    Wtb 87 GN t-top roller/project

    Looking to get back into a TR after a far too long hiatus. Looking for a roller with a decent interior. GN only with T-tops a must! 87 preferred but may be willing to go 86 if it's a good fit. Can pick up myself with trailer, looking to stay under $5k. Thanks. Joe
Top