Search results

Was running fine, and all of sudden at 35-40 mph it stumbles flat on its face.Cant even get mph higher than that.L8 was at 250 and TPS was at 1.58 when the car was running bad.Pluged the plugs and there all foulded out with black carbon.FP is set at 43psi.

Guys i ran across a person who,s father has an 86 GN LeSabre with 16,000 miles.He's asking $15,000.

Does any aoto parts stores sell these,like Auto Zone ?

My87 GN has a stumble at idle, and when i take off from a start it runs rough , but clears out at 35 mph and up.Even when the car is warmed up it still does it.FP 43,TPS .44,WOT 4.60.All i did this winter is change head gaskets to cometics which leak by the way.I run 100 octane in the car and...

I know this has been talked about already , but what should i do? Had my intake ceramic coated, thougt that would be a good time to replace head gaskets with the cometics.I put new ARP bolts in and torqued them to their specs in the proper sequence.I didnt put any copper spray or anthing on the...

where can i get in illinios,isaw some say Home Depot,is this true?

Where can i get some tablets for the raidator?Will the parts counter at the dealers carrying them?

Anyone using the delete pulley have any issues with the belt.Mine keeps throwing the belt off .

Guy's i need to rebuild my master cylinder, it has internal leakage.Can i buy seals and do it myself , or buy a rebuild , or send mine out.If i can get kit to rebuild where can can i buy it from?

Where can i get one , and how much are they selling for?

I just replaced mine with a rebuilt.Was wondering before i turn the key on are there any precautions i need to take?I still have to bleed the lines, but do you prime the pump at all?

Need some help here guys, i recently changed my head gaskets and bolts , and had intake ceramic coded and the down pipe.Also had plenum polished,anyway's put it back together and started the car, it ran fine then had a stumble at idle and code 42 came up.So i shut it off for the night and came...

Guys i decided to take the compressor out since it's not working anyways.What do i do for a belt size.Do i need to buy one of those bypss pulleys they sell on e-bay, or is there another route i should go.

Is everyone using the washers ARP supplies with the bolts, i noticed the stock bolts dont use them....

How do you remove the exhaust housing off the turbo.I pulled out the bolts ,but it will not budge.Does it unscrew or just pull off.Its really new , about 400 miles on it.

Guys i need to have my chip ajusted to lock the converter up.What speed should i set it at for a street car...

Looking to replace my stock rocker arms and shaft.My stock heads were ported and polished , new Manley severe duty valves,177.5 intake,1.5 exhaust,Isky springs 135lbs seat.Any one have any suggestions on size and brand?

How can i check to see if the compressor is good without any freeon .The unit is in the car.

Need help guys,all i did was adjust IAC,TPS,and FP. Then filled it up with 100 octane and now at 5lbs of boost my knock guage goes red and my O2's are low with high retard.The scanmaster shows no MAL.Could the gas be bad,or knock senor bad.Where do i look? :confused:

Man i don't know what went wrong ,but everthing is f #!# up.Car was running good except for an off idel hesatation ,so i tried to adjust the IAC,TPS ,FP to fix it.I set the FP to 43psi because i have a turbo tweak chip.The IAC were around 5-6 so i tried to raise them to 10-20 but the RPM were...