Search results

Another Center Cap made a break for freedom.... Now I'm in need of 1 GN Center cap - preferably new. Thanks, Mike

3VWSA61H8WM148316 Co-worker looking to buy a VW Jetta for her daughter. Thanks for the help!

WTB GN stock wheel Center Cap I've lost one somewhere on the road. Only need 1 at this time Thanks! Mike

Anybody have a timing chain tensioner bolt they will sell me?? Reply and I'll contact you! Thanks, Mike

Selling a PTS 2600-3000 xtreme 9 x 11 converter. Great street /strip converter, stalled @ 3000 on my mild build. Converter in perfect shape, locks perfectly. Purchased in 2002, approximately 12,000 miles. $275 and I'll ship to you - it is boxed, ready to go. I'll take paypal. Mike

Hello Mike, I've run into a problem with my Extender chip - part # BWL57BIF. Seems it won't lock the converter anymore. I've tried reprogramming at different speeds with no luck. I put in my TT chip and it locks the converter with no problem. Would you contact me about getting this...

I have a set of 6 36lb Ford Blue top injectors for sale. Roughly 20k since they were cleaned. They have performed flawlessly for me the past 5 years delivering 115mph trap speeds and an easy 25mpg on the highway. If you act now, I will include the following chips: -Thrasher 92 with theft...

Super Service on the gasket set I bought! Less than a week for me to mail a money order and receive the gasket set via priority mail from John. :) :) Thanks John! Mike

I have just finished rebuilding my engine after a problem with the thrust bearing. Looked like a cap misalignment problem that caused the failure. The transmission has about 3K miles on it, and I have a 2800 stall PTS Xtreme and I don't think these are causing me a problem. BUT......I will be...

http://www.turbobuick.com/forums/showthread.php?s=&threadid=83861 Pulled engine earlier this week. After the tear down and close examination the answer to the bad thrust bearing was staring at me. The #1 cap and #3 cap had the arrows pointing to the front of the block. The #2 was...

May need an undercut after a wiped thrust bearing. (.010/.010 now) Anyone have any problems? Mike

Found some glittering bearing material in oil last week. Uh-Oh..decide to pull oil pan this morning and found my thrust bearing is down to copper on both sides. Looks like some heat build up has occured also from the looks of the discolored bearing. Bearing does not look good..scratches and...

Saw the good-bye episode last night. I will miss the Juggies, Beer boy, Adam and Jimmy and of course - girls jumping on a trampoline. Wife never understood why I liked the show...She never saw the twins strip basketball game either:D :D :D

Car has been suffering through the dreaded "fishbite" condition where there is a surging/stuttering effect between 45-60mph once the converter is locked. I have adjusted the cam sensor repeatedly the past weekend trying to find its sweet spot. I got it set with no surge and minimum fishbite...

Anyone running a 15 x 8 American Eagle alloy on the rear of their car? Noticed it is made with a 3-1/4" backspace which may necessitate rolling the fender lip. ( Plan on running either 255/60 or 275/60 tire). Any comments would be appreciated!

Last Christmas the Stock MAF died on my car. During the past few months the following happened: Borrowed a MAF off a buddies 89'TTA and used for a month decided to get a A-1 Cardone from the local Advance Auto. Ran well, but throttle response was not sharp. In April replaced tranny and...

I knew I had a race today............ Like a lot of you guys, I generally can't buy my way into some honest stop light action. Against ricers it is 2lbs of boost and they are fodder for the GN. Most cars won't even try to race me. On my way home from work on the 2 lane bridge over the...

Need some help with a D5 convertor that won't lock. 1. Established that all electrical contacts are in order. 2. Dropped pan and checked solenoid. It opened and closed when I pulled it out of the transmission and put power to it. 3. Reinstalled it. Transmission shifts well in all...