Search results

My uncle - gnbeginer - on this board past away early Tuesday morning. He was way to young to pass away as he did. He died of a massive heart attack, he was only 47. He had a severe stroke in late march which left him with a deterating heart condition. My name is Ricky, he was always messing with...

going ls - tired of all the problems that keep coming up on the v-6 build. Here's what I have: 109 bored .030 over, billet caps front to rear and a girdle - 750.00 4340 forged crank - 500.00 4340 h-beam rods with j&e pistons(.030 over) - 450.00 comp roller 212/212 - 150.00 comp 885 roller...

both are basically new. knock gauge was hooked up and used for about 2 months. control was in car but never hooked up. gauge - 75.00 controller - 100.00 yes those are shipped prices. TIA

Ok - I am considering going to e-85 on my new build. I am going to be around 600 - 650 hp, what do I need to support approperiate fuel to the motor? I have a double pumper and fuel lines are stock - but i can replace with bigger if needed. I just need to know what i have to have to support said...

Well car is sold - so i need to get rid of the extra parts i have. First i am going to list are parts i know i have but have to get over to storage for pics and get them home - so please bare with me. first - several interior parts - plastic trim pieces including a nice dash. I have door...

like the title says - I'm parting out my 85 gn that's been converted to intercooled. Pretty much a complete car with brand new(never fired)motor. if you are interested in any parts or the whole car - let me know. Reason for parting out/selling - I've lost interest. I'd post a pic of the car -...

anyone have a set of 8.800 push rods they are not using? TIA

I need the 3 bolts that a/c compressor to the accessary brkt. have the stud and all the brkts. just need 3 bolts. TIA

I bought a double pumper a lil while back and it included wiring but no instructions of how to hook it up. Could someone enlighten me on the best way to hook it up using a hobbs switch? TIA

what should these be torqued to? GN1's and arp studs. tia

Ok - i was put in the direction of a good used sfi flywheel. Went over it it over and found it was never installed on the motor. guy changed direction and went ls1. So i bought the flywheel - got home crawled under car and started to install said flywheel. I have installed several flywheels over...

Changing my combo again and need a stock intake system. what ya got?

changing direction on my combo again. I have a functioning m&a intake up for sale now. possibly do a trade for a stock lower/upper intake with throttle body and fuelrail and coil brktry. Asking 750.00

anybody have a diagram of how the guide plates and rockers are to be installed on 14 bolt champion heads? had it once but cant find em now. help please tia

does anyone have Andersons performance phone number or e-mail? need to get ahold of him for some parts. thanks

Does anyone know the off-set for the scorpion rockers that go on the GN1 14 bolt heads?

need a dutt neck - anybody have one? with or without coupling dont matter. also need a shroud for a facorty intercooler. lemme know thanks

title says it all. looking for a good harness. friend jus bought a 84 with a 86 drivetrain, somehow they made the 84 harness work. and it is all kinds of hacked up. thinkin its best to get the wire harness replaced with the right one. prefer one that not all hacked up - the fewer the splices the...

A friend of mine just got his first gn back in march. He brought it out to show it off and the trans stop shifting. Granted its a 84 with the i/c conversion done to it, but its a running and driving gn for 5k. So we were lookin at a couple things and that's when he told me it had been sitting...

can someone tell me the actual measurement between the bottom of the cam journal and the top of the crank journal. Had billet caps installed on block - suppose to be .002 cut on block but a stock t-chain fits it really tight. Wondering if shop really bored and honed caps to block. TIA