Recent content by Amab145
Welcome!
By registering with us, you'll be able to discuss, share and private message with other members of our community.
-
T-Top Seal Kit
Hey guys, who makes a good t-top seal kit? Finishing my whole resto and I’m at the t-top portion and have read horror stories about most kits. Any suggestions?- Amab145
- Thread
- Replies: 0
- Forum: The Body Shop
-
Light Sand Gray Door Panels
Thanks. GBody parts said they went discontinued a few years ago and won’t be getting them back in. I just shot an email to SMS to see if they have fabric I can order and then just have mine recovered. Appreciate the lead on the fabric!- Amab145
- Post #3
- Forum: Parts wanted
-
Light Sand Gray Door Panels
WTB: Looking for light sand gray upper door panels for my 84’. Searched everywhere from vendors online and can’t seem to find them anywhere. Anyone have anything new or used? Thanks!- Amab145
- Thread
- Replies: 2
- Forum: Parts wanted
-
Metal pieces in Oil Pan
Sorry for the delay here fellas, been traveling non-stop for work the last few weeks. Only one lifter wasn't broken and both sides of the lifter body on the base of that particular lifter had some visible marks from contact with the cam lobe. I contacted Mike at TA who's been a big help, he...- Amab145
- Post #12
- Forum: Engine Tech
-
Metal pieces in Oil Pan
Lifter bores look fine and when I orientate the lifters on the bench as if they are installed in the car, each break is on the trailing side of the lifter, but the leading edge does have some stuffing on each as well. Cam lobes look pretty dang good considering. I don’t see any deep grooving...- Amab145
- Post #7
- Forum: Engine Tech
-
Metal pieces in Oil Pan
Well, here’s an update. 11 out of 12 lifters have broken bodies. What’s strange is each body is broken on the side that is closest to the cam. Any thoughts?- Amab145
- Post #4
- Forum: Engine Tech
-
Metal pieces in Oil Pan
I had it built brand new several years ago. Not a used part in it. Was running fine when parked. Looking up from the bottom, from what I can tell is it looks like the bodies of several of the roller lifters cracked around the roller. All the valve lash is good, but it looks like several...- Amab145
- Post #3
- Forum: Engine Tech
-
Metal pieces in Oil Pan
Well, dropped my oil pan this morning to replace a pan gasket with a very minor leak and found these pieces inside the bottom of the pan. Car has been running fine, no loss of oil, pressure or miss that is noticeable whatsoever. Any ideas on what these can be from? Maybe part of a lifter...- Amab145
- Thread
- Replies: 14
- Forum: Engine Tech
-
Fuel info..
Good info, thanks Chuck. I wish I could find a chart like that for the C12 i've been running.- Amab145
- Post #2
- Forum: Engine Tech
-
Racetronix Fuel Pump Issue
Agreed, I've got a pair of DW300's and have had good luck also.- Amab145
- Post #25
- Forum: General Turbo Buick Tech
-
-
Scanmaster G and Hotwire Kit
Selling a Scanmaster G (non-XFI) and a Casper’s Hotwire kit (12 gauge kit) Scanmaster G was installed for about 3 weeks before I switched over to an XFI with the eDash, virtually no use - SOLD Casper’s Hotwire 12 gauge kit - $45- Amab145
- Thread
- Replies: 3
- Forum: Parts for sale
-
RJC Stainless 3” Downpipe
Sorry for the late response. It’s sold, he bought it lol ^- Amab145
- Post #7
- Forum: Parts for sale
-
Stock Shifter Stalk
I did see that from G-Body. Hoping to find a used one as that's a cool piece from them but super expensive. That'll be my last resort for sure!- Amab145
- Post #5
- Forum: Parts wanted
-
