Search results

Anyone know of a good place to take the GN to get dynotuned in the central jersey area. Willing to travel some

I am not sure if this is the right place for the answer, but I am in the midst of repainting my GN and may actually do a body off resto. I would like to know if anyone has replaced the body bushings and what brand they used or who they bought them from. Any suggestions would be a great help.

I am in need of new rear springs. The car is basically a weekend street car with limited track use. I do have airbags, but the springs are shot. What is a good brand to go with and should I get lowering springs??? I might as well do all the corners also. What about bushings? I am trying to...

http://josh.swoca.net/antiricer.wmv I don't know if this video has been poster before

I have read over the boards about both and gone to the T-Link website, but still am not sure what is the best tuning tool. I have a scanmaster right now, but would like to save the information that is being recorded. I se T-link is always being upgraded, how often is data in the DS being...

I have a 3.5" MAF, T+ and extender chip, do i still need to run the ats?

WHich tire is wider? The BFG 28" or nitto 28" drag radials?

Who makes an extender chip. I know Bob Bailey has one does anyone else. Also how do i get in touch w/ him. Eric From Turbotweak recommended him because im upgrading the the T+ from stock MAF. So if anyone is looking for a TurboTweak chip for 009's and alky i have one.

Does anyone know if the translator will work w/ the LT4 MAF sensor with the 3 prong system?

I need to replace my MAF again and no sure if I should spend the money for the stock if it is going to just die on me every year. What is recommended for the LS1/Lt1 MAF's. IS there a difference between the 2. I have seen 3" and 3.5" which is better to go with. Where can I buy a stock MAF so...

I need my frame notched and was wondering if anyone in New Jersey knows how to do it or can do it for me. Even Pennsylvania will be fine like the philly area.

I installed a set of BFG 275/60/R15 DR's last friday and have nothing but problems with them rubbing somewhere. I installed spacers bc they rubbed the frame on the one side now i notice i got a gash in the right side tire on the outside from a sharp edge on the wheel well. The left side seems...

I am getting and error code 45. When I got the code the first thing i did was turn the fuel pressure down, I am only running 41#line off. That didn't work so i changed the 02 sensor disconnected the ecm for a little bit then hooked it back up. Turned the car back on and same code. My MAF...

How much more of a gain is a TA60. I have one but would like to know how much of a difference in hp there is from stock.

If im going to run 275/60 tires my speedometer will be off, i want to know is there a reducer cable i can buy for that. Where can i get one also? I know esp makes them for different rearend gears. If anything how much will the speed change and does anyone have to calculation for it?

What are the better size tire for driving on the road w/ occasional track time BFG drag radial 275/60/15 or 275/50/15 and these are on stock wheels.

Which is the best turbo upgrade for my set up? I do have an upgraded cam thats not posted. Doesn't have to be stock looking. I was looking at the Te44 or TE60. What about a TE61?

Can I reuse the gasket between the turbo and header? i Have the non copper gasket. I have to switch back to my stock turbo bc my new one has an oil leak so its only temporary.

When i let my car idle it tends to let out a lot of white smoke. It doesn't seem to have a distinct smell to it. It will clear out when i drive, but then when i stop it sometimes comes back. I turned my fuel pressure down thinking it was too rich. I have it set at 40psi line off. My oil...

What is wrong w/ using tap water? I have a well w/ $5000 filtration system that takes everything out of the water. Do I still need to run distilled water w/ my alky system?