Recent content by mommasGN

Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!
  1. M

    Rollmaster chain "stretch"?

    The cs7020 is the correct set for our engines correct? Rolmaster website says this is the gold version.
  2. M

    Rollmaster chain "stretch"?

    Thats an idea running through my head. Use this chain with a new set of sprockets, maybe a .004 or .005 oversize. I'm assuming if i buy a new chain, it will stretch and end up the same way. This one wasn't making any noise or causing any issues.......i would just prefer a chain with no slop.
  3. M

    Rollmaster chain "stretch"?

    OK Chuck, holding the chain straight out, it droops right at 1/2 inch.
  4. M

    Rollmaster chain "stretch"?

    I'll check the drooping holding it sideways when i get home. Yes "oversize" to accommodate for the line-bore. This is from the rollmaster tech pages. Oversized gear sets are available for align honed/bored engines. The compensation is NOT in the chain itself, but in the two gears. The...
  5. M

    Rollmaster chain "stretch"?

    My Rollmaster chain has slightly more that 1/4 inch of slop. Engine was built in 2020 has about 40 track passes and maybe 8000 road miles. I have my timing cover off to fix a coolant leak,, and of course check the chain........ and its very sloppy. It is already the .002 oversize kit. I...
  6. M

    Scanmaster G - Please Help

    i gave up on the Bluetooth with mine. I tried several different android phones and tablets (with aldldroid)......none worked. 2 different laptops, one never worked, the other, I got the Bluetooth working, but it would crash the PL software after about 30 seconds. I just use the old faithful...
  7. M

    Vacuum block elimination

    Dont have any good pics, but i went with and intake spacer and plastic lines with pushlock fittings. I was worried about the fittings leaking. I used a smoke machine to check for leaks several times with none to be found. I have also(twice) adapted my cylinder leak down tester to pressurize...
  8. M

    Volt Blaster vs Boost a pump

    I'll post a log with the volt booster vs the BAP. With no other changes, I feel my AFR was more steady and half a point richer with the BAP. Also.....i noticed no other difference in how it ran without the volt booster........ i.e: more voltage for coil, injectors, etc. In my opinion......If...
  9. M

    Volt Blaster vs Boost a pump

    I just switched from a volt booster to the boost-a pump. I went to the track yesterday and was impressed. There was nothing wrong with the volt booster, i just got a good deal on the BAP and liked the idea of it. I Checked and double checked that it was sending the correct 17 volts to the...
  10. M

    Caspers cam sensor cap

    Brand new with original box and instructions. Only installed with engine on stand. Never ran. $60 shipped.
  11. M

    Kenne Bell boost-a-pump

    I'll buy that from you. whats your paypal?
  12. M

    Stalls only during burnout

    sorry for the delay. between work and kids sports...... heres a log of a run at the track. from frame 2050-3000 was the burnout attempt. you can see it took several attempts and i was finally able to do a full burnout, then make my pass with no issues.
  13. M

    Precision 66mm exhaust housing .85

    put me in line
  14. M

    Stalls only during burnout

    i have a volt booster so i am at 15.7 .That was a thought i had. battery in factory location Once i get to my laptop, ill share a log.
  15. M

    Stalls only during burnout

    Yes, it does it while the throttle is still held open.
See more

Online statistics

Members online
13
Guests online
6,534
Total visitors
6,547
Totals may include hidden visitors.

Latest posts

Newest members

Stay Connected

Back
Top