Search results

1991 Z28 hardtop, bright blue, with a D1SC procharger with a Front mount intercooler and 36# injectors. Approx 10,000 on rebuild. Has a bored .030 over 5.7 with forged pistons and balanced rotating assembly. Stock rear end and tranny, both have approx. 145k on them. Motor is an L98 with stock...

1991 Z28 hardtop, bright blue, with a D1SC procharger with a front mount intercooler and 36# injectors. Approx 10,000 miles on rebuild. Has a bored .030 over 5.7 with forged pistons and balanced rotating assembly. Stock posi rear end and transmission both have approx 145k on them. Gray leather...

I'm considering selling my Camaro. What do you guys think it's worth? It is rust free. Has a bored over 5.7 with forged pistons and balanced rotating assembly. It has a D1SC with a FMIC and 36# injectors. Leather seats in good condition. The paint is still glossy. Pic...

1987 Buick T-Type Y56, WO2......... Perfect body absolutley no rust, 90% perfect paint, mint interior. But it needs a cam and lifters, how much is she worth? The Goodies: forged TRW pistons double roller timing chain o'ringed heads, balanced rotating assembly,Ported and polished iron heads...

Best offer! 1987 Buick T-Type Y56, WO2......... Located in Kansas. Tinted windows. GNX badges were put on the car to make it a clone. The car is white in color, but came black from factory. Engine has fresh rebuild with less than 5000 miles on it. RPO codes still in trunk. forged TRW...

1987 Buick T-Type Y56, WO2......... Located in Kansas. Needs new cam and lifters, other wise runs PERFECT. Has new aftermarket header panel and new after market rear fillers that need painted. Needs one fender vent. Small dent in hood. Straight body NO RUST. Has minor chips in paint. Tinted...

We have a fresh rebuild with only 600 miles on the engine. We have 80 psi oil pressure :eek: , but we have very very little oil coming up to the top end :eek: . Only two of the rockers have some oil on them and it isn't very much. Seems like with 80 psi we should have oil shooting out everywhere...

Is there any identifing mark on the stock flywheel for an 87 GN? A casting number or does anyone even know the amount of teeth? Thanks in advance! :confused:

We are rebuilding our 87 GN engine, and we just have one basic question.... One of the Piston rings has a Beveled edge does it go in the top compression ring land or the second compression ring land?

We are finally putting my engine back together and we are needing to know the acceptable main clearance. We are using plastigauge in a COLD (didn't fire heaters up yet) shop at about 40-50 degrees. The measurments we got are right at .0018- .002. Are these acceptable?

Well I am shopping again for a new cam. We just bought a new lunati cam and lifters, and had horrible luck with it. 3 lobes are gone. So after new oil pump, new timing cover and some other odds and ends, we were getting ready to change out the lifters and noticed the cam was flat. My...

We have the caspers Cam tool and we are needing to check the timing. We have no more stickers and didn't think of making a copy. Does anyone have a copy or know where we can get these? Or even a measurement? Thanks

My husband went to rebuild my oil pump today and when he took it apart the timing cover was worn pretty badly. We will be pricing one out tommorrow. Can anyone tell me what we should expect to pay or is there a better solution to buying a timing cover?

Ok here is the deal. I have had alot of problems with my car every since we bought it. We just recently rebuilt the engine, now my hubby says it is running rich. At WOT I get alot of black smoke and the car is stalling as if it is cutting out. Falling completly on its face. Feels kinda like...

My oil psi is at 10 when I am at a stop light and then at 45mph it is at 25. Is this about right or too low? :confused: Concerned because the 91 z28 with a 350 has at least 30lb at idle. If it is bad is there a certain brand to go with or rebuild kit to buy? Standard? High Volume? For...

My husband is the big Camaro fan and I am the Buick fan. lol Well, he is getting a Pocket programmer to burn his own chips and he was wondering if with that he could also burn chips for the buick does anyone have any idea? :confused:

We are just kinda of curious on this one but, we just changed my oil about 75 miles ago and had to drop the oil pan to check something out. And my husband noticed the oil is a black as night. Any idea what could cause the oil to turn black so fast. We use mobile 1 synthetic. Thanks.

I am trying to get Stock lifters for my 87 Gn and I am running into a problem. Chevy dealer gave me a part number of 5234485 Buick 5334486 Does anyone know which one is correct? Thanks

Ok I have a fresh rebuild on my engine, the only thing I am lacking is my turbo is on its way out. For the rebuild we replaced main and rod bearings (Clevite 77), rings, head gaskets, all other gaskets, cam, lifters, had the crank turned and engine looked at and cleaned. Well we have about...

Me and my husband are pretty new to these cars. We just rebuilt our first on and finished in on nov 19, 2002. We are trying to find someone that is familar in tuning these cars. That would either be interested in taking a look & a listen. To see what they think needs to still be done. Either our...