You can type here any text you want

Recent content by jmd

Welcome!

By registering with us, you'll be able to discuss, share and private message with other members of our community.

SignUp Now!
  1. J

    1987 Rear differential F/S in Phoenix

    SOLD 3.73 open 8.5" 10-bolt from 1987 442. No noise, no problems. Needs one drum. It's been forever since I shipped one (disassembled) so I don't know if that can still be done ground for reasonable cost. But I can try for a serious buyer. $500.00
  2. J

    Need help wiring 3rd and 4th gear pressure switches

    4th p.s. is pointing at the ground, visually "near" your cat. IIRC, your other is a temp switch. But don't quote me yet.
  3. J

    Doing a vacuum swap, dual or single diaphragm booster?

    One of my cars had a single; the other a dual. Never noticed a difference when they had the same brake on each. So I question the "twice the assist" bit. The Orca 91-96 B/D bodies have an offset pushrod on the booster. Stick to the 90-down for the booster. Their master cylinders are...
  4. J

    Front Lower A arm bushings

    I have one car with del-a-lum. The other has high-durometer Moog. They were available around 2004 when I re-did the bushings & balljoints. F-body, 2WD S/T-series and G-body all have different bushing sizes in the LCA. So 1LE bushings only fit the F LCAs. There is a little bit of squeak with...
  5. J

    TH400 4L80E Yoke, Broken or Good

    I need one for mockup. Splines must slide over a good 32 spline output. Outside must fit a good bushing. The rest can be hammered. :)
  6. J

    tweaked frame...what to do?

    slim said it. GM had a few models pre-'78 that cracked frames; the K5 and 68-72 A-body truck specifically (coupe too IIRC) So you won't have a perfect one after it's seen launches, miles etc. Have it put on a frame straightener or if there are other underlying reasons it's bad, consider...
  7. J

    Looking for a new aluminum master cylinder, yes I've search

    I decided years back when a friend found a new one that it wasn't worth almost $200 difference to avoid a perfectly good reman. We actually both went with B-body units IIRC. No problems, no regrets on the reman in my case.
  8. J

    Alternate Output Shaft Bushing Driver tool(s)

    Snap-On finally called back and indicated o.d. as 1.496" with i.d. as 1.494". :rolleyes: I already got something lathe-turned from steel pipe so whatever.
  9. J

    Alternate Output Shaft Bushing Driver tool(s)

    Atec sells separate driver puller combo for 1 & 5/8 C6 apps. No word back from SchnapOn.
  10. J

    Alternate Output Shaft Bushing Driver tool(s)

    SnapOn lacks the dimensions of that tool.
  11. J

    Alternate Output Shaft Bushing Driver tool(s)

    What are you using for the install of the output bushing in the small GM 27 spline transmissions when a particular case / tailhousing is being problematic? I have this: E-Z Extension Housing Bushing Tool | Remove and Install GM, Ford and Chrysler Extension Housing Bushing | A to Z Tool On...
  12. J

    Lot's of parts... LQQK and make an offer

    AM/FM w/ no cassette. Is that right? $15 and shipping to 85032. (or I can send you a fedex ground label for dropoff at kinkos) thanks
  13. J

    Extra parts FS

    Pic of the plain jane radio please.
  14. J

    BIG PARTS LIST, My Biggest Parts List Yet!!! Lots of parts added.

    Pics of radio? I assume the am/fm and clock/station display work, but the cassette is busted like all of them. thanks
  15. J

    88 monte ss tranny

    that's what I paid for mine yesterday. With D5. Hope the POS works. :o
Back
Top