Recent content by Yah's 87

  1. Y

    getting idle for MAF translator

    87 GN daily driver has tt chip and injectors., have been driving the car for the past few months, runs out good , just doesnt want to idle. Have a 3.5" MAF sensor connected to a 3" intake setup. This car will not idle, and I have replaced and checked all vacuum lines. Adjustable fuel pressure...
  2. Y

    any suggestions installing a new turn signal switch?

    this is the circular plastic piece with the wires that is one unit and has a harnes connector on the end of it. The wire length is about 18 inches. does the steering whee come off to install? thankx!
  3. Y

    what is a good part # for a turn signal switch and also a windshield wiper motor?

    just seeking a decent source, not wanting a $400 turn signal switch, or a $700 windshield wiper motor. Thankx!!!!!!
  4. Y

    IAC at 90 and screw out all the way

    So this is a daily driver with a 3.5" MAF and a 3" intake tube all the way to the turbo. Has MAF translator and scangage. My settings are rich at idle and plus 14 % rich at WOT. car likes to stall when downshifting to an idle setting. with the IAC adjust screw unthreaded out, the throttle...
  5. Y

    looking for a 3 inch downpipe for a daily driver GN

    best to just start a fresh thread to be current
  6. Y

    looking for a 3 inch downpipe for a daily driver GN

    i bought the TH dp, and i think the TA already sold
  7. Y

    what size shims should I order for comp cams 980 ?

    the best info Ive learn so far is if removing the dampeners is to use a .40 for them . and it seems as if some have just straight up installed the new springs with the dampener.
  8. Y

    ngk UR5 2771 wont thread into hole

    i just rethreaded the old one back in for now, i tried 3 different plugs, and then just stuck the old one back in there, #1 cylinder, theres a small plate that is a guard by the manifold that might be the concern. I used two different deep well sockets, one a spark plug deep well and a regular...
  9. Y

    ngk UR5 2771 wont thread into hole

    Imma trying to install these and I notice the shoulder is shorter and different. Has anyone had the same pleasure im having trying to install these?
  10. Y

    what is best # for the IAC? i have scangauge and keeps stalling

    good thankx, im running quite well now, it was a new IAC install
  11. Y

    what size shims should I order for comp cams 980 ?

    this is a daily driver and has stock internals. Ive done valve springs before on a diesel engine. With the same spring actually. Anyway , I dont know the height that is best, nor the shim sizes to order, thankx!!!!!
  12. Y

    what is best # for the IAC? i have scangauge and keeps stalling

    daily driver, already set the TPS , and checked vacuum lines. do have delete on the exhaust back pressure valve on drivers side bank. I have a MAF translator and pretty much run close to 128 blm at WOT and idles decently a little rich. thanks for the wisdom, Ronjon
  13. Y

    what is the beast brand of IAC to buy?

    th end just fell out of mine, its time to order me one. Im inclined to buy delco , any brand better to recommend? thankx, ROnjon
  14. Y

    have 4 ways flashing, no right turn signals .

    the wires appear to be good and intact.
  15. Y

    have 4 ways flashing, no right turn signals .

    i just installed brand new bulbs , and 4 way flashers work. just not the turn signal for right side. thinking its the switch on the column
See more
Top