Converters, Turbo, Cam Kit, and More.

[9SECVSIX]

TCS 9"x11" LU Converter. Fresh from the shop with complete overhaul. 550.00
CPT 9" #19930-"N" 3200-3400 Stall. Low Mileage but it's fresh from Pat's 600.00
MP-T70-"P" trim big shaft turbo with T'netics .82 a/r 3 bolt ceramic coated housing.
Actuator and dog ears included. 4" Inlet-2-1/2" outlet. BRAND NEW...650.00
Poston BRAND NEW 107 flat tappet cam (202-202@.050" .430 lift) Two new sets of springs 80lb
and 100lb. New set of hyd lifters. 160.00
CPP-(Mark Brown) Liquid intercooler. (used been 9.30@145) 2-1/2" in 2-1/2" out) 250.00
All items above are plus shipping.
BRAND NEW TR Brass proportioning valve....70.00 shipped
King Main Bearing Set#MB 482AM 010 This is for a .010" journal and a .010" Thrust 35.00 Shipped.
Serious inquiries can email me for pictures.
Thanks
B.

 

[9SECVSIX]

Pictures sent to those that requested them.
I just spent 250.00+ to have this 9x11 completely rebuilt and 150.00 to have the CPT given a clean bill of health.
Both are fresh.
Thanks
B.

 

[9SECVSIX]

All parts still available.
B.

 

[SuperSix]

What's the stall on the TCS unit?

 

[9SECVSIX]

What's the stall on the TCS unit?

it's labeled 3400, I asked the shop to snug it up a bit.

 

[SuperSix]

Thanks - I need ~3k. GLWS!

 

[9SECVSIX]

Pics added ...

Here are some pics ...

 

[GNWANTED]

CPT 9" #19930-"N" 3200-3400 Stall. Low Mileage but it's fresh from Pat's 600.00
Did you have the stall changed on this one? I think "n" would be 36-3800 stall. Do you have any other build specs on this converter?

Thanks,

 

[9SECVSIX]

CPT 9" #19930-"N" 3200-3400 Stall. Low Mileage but it's fresh from Pat's 600.00
Did you have the stall changed on this one? I think "n" would be 36-3800 stall. Do you have any other build specs on this converter?

The CPT was built for a good friend of mine in Mass...he has a 276" Stg motor with M&A heads. From what he told me I don't think it was that loose (36-3800). I thought of using it with a much smaller turbo than his 70GTQ so I had Steve Barr check it out, he said he could only move the stall about 200rpm due to the brazed fin design. The picture of the turbo showing the part# didn't make it to the site, I'll try that again later .You can call me if you wish, PM me for my # The turbo 100% fresh.
Thanks B.

 

[YAKO]

9secvsix is a excellant vendor

 

[J-B Racing]

9secvsix is a excellant vendor

x2

 

[9SECVSIX]

Couple nore ...

Here's a couple more pics ...

 

[9SECVSIX]

bump!

 

[9SECVSIX]

Cam Kit is SOLD. Don't sell these turbos short, this is a lot of turbo for the money and are excellent units. I've installed several. Will consider reasonable offers on the converters. Thanks. B.

 

[TurboDave]

Got the cam kit already Brent!! Thanks for the fast delivery and great packing!

 

[9SECVSIX]

I would consider a smaller turbo on trade (new only) 60-63 "P" trim.

 

[9SECVSIX]

9"x11" converter SOLD
9"CPT Still available. Fresh from Pat's 600.00 shipped
MP T70 Turbo available. Brand New. Excellent unit. 650.00 shipped
Shipping is to lower 48 and Canada.