PARTING ANOTHER PARTS CAR,87 T-TYPE, PLUS BIG LIST OD PARTS,(Jan.04th)

[Intercooled88s]

roc87

E mail sent.

 

[Intercooled88s]

Ttt

 

[my85grandnation]

Hey intercooled. Do you happen to have any of the metal heat shields that bolt onto the front right side of the passenger side valve cover on the 84/85 hotair cars. It is held onto the valve cover with a 10MM nut and then also has a hold on point on the back of the A/C compressor. It protects the plugwires from the heat of the up pipe. If you have one will you please email me pics and a price shipped to 80829 to dthom8787@yahoo.com Thanks

Dusty

 

[Intercooled88s]

You dont need the shield between the heat heater pipes and intake, give me a little more detail. I just got home and Im a little tired. I should have it I've cut up a ton of 84-85 turbo cars.

 

[my85grandnation]

The one Im looking for is not the one that covers the heater pipes. The one I am looking for is a little almost square piece that is 4 or so inches wide by 4-5 tall that has a bend in it to wrap around the side of the valve cover. It goes on the front right side of the passenger side valve cover. The valve cover bolt in this location has a stud coming off the top of it that the little 10MM nut screws onto to hold this plate in place. The shield is also held in place on the back of the A/C compressor mount by a 1/2 in bolt. The plug wires run behind it to be protected from the heat of the up pipe. The 84 and 85 cars had them on them but not the 86/87 as far as I know. Two of my 85's have them but the third one does not. I have tried to get a pic of it but the up pipe is in the way and you cant see it. If you need I guess I could take my up pipe off to get a good shot of it, its just that that is such a PITA. Let me know. Thanks Dusty

 

[my85grandnation]

I just found this pic in the hotair forum. If you look closely at the passenger side of the engine, you can barely make out the shield I am talking about. It is the vertical piece of metal between the uppipe and the valve cover. http://www.turbobuick.com/forums/attachment.php?attachmentid=4753

 

[Intercooled88s]

my85grandnation

Ok I know what your talking about now. I'll have to look, to see if I can find one.

 

[Intercooled88s]

Ttt

 

[my85grandnation]

Ok thanks. Let me know if you find one. There are two slightly different versions of it and I would prefer one over the other so if you find one please email me picks. Thanks Dusty

 

[Intercooled88s]

my85grandnation

Do you know what the part # was originally on it. Most of the 84-85 cars Ive parted were missing this bracket.

 

[Intercooled88s]

Ttt

 

[Intercooled88s]

Ttt

 

[my85grandnation]

I called GM and got the part# for it. It is no longer available from GM but heres the# 25521617. Let me know. Thanks Dusty

 

[Intercooled88s]

I looked a little today and found a small shield I wasnt sure what it was from, I will check the number stamped on it to see if its the part your looking for.

 

[Intercooled88s]

Ttt

 

[skostur79]

got any hot air exhaust manifolds? left and right

inlet pipe ? (prefered with out the braiding)

cylinder heads to get redone (so i can leave my engine running untill done)

lastey a top windshelid molding black


prices if you have and shipping to 44060

thanks for your time

skostur79@comcast.net

 

[Intercooled88s]

skostur79

E mailed you.

 

[my85grandnation]

Any luck with that shield?

 

[Intercooled88s]

I have a small bracket that I think may be it , it has a part number stamped into it, I will try to get down to my shop today and check it against the part # you gave, I will post to let you know.

 

[my85grandnation]

Even if it is not the same part# would you take a pic of it and post it for me or email it to me. The reason being is that I have seen two different versions of the heatshield but yet GM only lists one variation. Thanks Dusty