jpwalt1987
Well-Known Member
- Joined
- Nov 9, 2003
- Messages
- 1,885
Items will continue to be added to this list as I get a chance to take pictures. Some of it is stuff that I have accumulated over the years and other stuff is due to the fact that my car is being returned to stock then sold. I prefer money orders but I will be setting up paypal again soon. If you dont like my prices then PM me an offer.
Delphi 95lb/hr injectors - less than 1000 miles -bought from Racetronix $354 new, Sell for $275 shipped
Rollmaster Billet Timing set - .010 oversize for blocks that have been line bored and are running a billet roller cam with the odd fire nose set up. $145 new, Sell for $75 shipped
3 to 4 bolt turbo adapter- was welded to header but was cutoff. What you see is what you get. $30 shipped
ARP Head Studs - fits 8 bolt GN1 Aluminum heads. Never over torqued. The short studs had some of the black coating come off. I was going to reuse them but forgot to ship them to DLS when my engine was built so I had him just put new ones on. $40 shipped OBO
T&D roller rockers - THESE MUST BE REBUILT!!! These are 1.60 ratio for GN1 heads. They have been ground on underneath to clear the valve retainer. One of the shafts is trash and will need to be replaced along with one of the rocker arms and its needle bearings. I would take the other apart and inspect it also. NO GUARANTEES.
$100 shipped OBO
CHIPS - I have a few misc. chips from over the years. They are for 009 injectors. The first one is from PTE (Joe Lubrant) and is an Alky chip with 24* of timing and 95%-100% duty cycle. $15 shipped
The second I have is a Max Effort Thumbwheel Chip. It is an 8 position chip. Dont know much else except that I went 11.30s on this back in 2000. $20 shipped OBO
The last chip I have is a dinosaur. It is a Bowling Green Customs Street Plus 10 chip for stock injectors. Best offer plus shipping.
PTE 70mm Turbo - Here is a link to the pictures. http://rides.webshots.com/album/553557263NNgwpB It has about 3000 miles on it always run with a turbosaver. Does NOT smoke and has NO in and out play. $700 plus shipping
ATI 10inch TH400 convertor. It has gone 9.20s behind a 274 motor with a 76mm turbo. I got it from Ted A. here on the board. It stalls 2700rpm @zero boost, 3000rpm @ 3psi boost and so on. $450 shipped
TH400 transmission - Built by our local race trans builder with an ATI transbrake, ATI aluminum pan, Red Eagle clutches and Kolene steels. It has about <1500 miles on it and zero dragstrip passes. Just street time. Cooler line pressure was verified to be under 35psi. Maybe lower I would have to double check. I just pulled the pan to reseal it (leaking) and the fluid looked good and there was nothing abnormal in the pan. New type F was used. $1000 plus freight.
Delphi 95lb/hr injectors - less than 1000 miles -bought from Racetronix $354 new, Sell for $275 shipped
Rollmaster Billet Timing set - .010 oversize for blocks that have been line bored and are running a billet roller cam with the odd fire nose set up. $145 new, Sell for $75 shipped
3 to 4 bolt turbo adapter- was welded to header but was cutoff. What you see is what you get. $30 shipped
ARP Head Studs - fits 8 bolt GN1 Aluminum heads. Never over torqued. The short studs had some of the black coating come off. I was going to reuse them but forgot to ship them to DLS when my engine was built so I had him just put new ones on. $40 shipped OBO
T&D roller rockers - THESE MUST BE REBUILT!!! These are 1.60 ratio for GN1 heads. They have been ground on underneath to clear the valve retainer. One of the shafts is trash and will need to be replaced along with one of the rocker arms and its needle bearings. I would take the other apart and inspect it also. NO GUARANTEES.
$100 shipped OBO
CHIPS - I have a few misc. chips from over the years. They are for 009 injectors. The first one is from PTE (Joe Lubrant) and is an Alky chip with 24* of timing and 95%-100% duty cycle. $15 shipped
The second I have is a Max Effort Thumbwheel Chip. It is an 8 position chip. Dont know much else except that I went 11.30s on this back in 2000. $20 shipped OBO
The last chip I have is a dinosaur. It is a Bowling Green Customs Street Plus 10 chip for stock injectors. Best offer plus shipping.
PTE 70mm Turbo - Here is a link to the pictures. http://rides.webshots.com/album/553557263NNgwpB It has about 3000 miles on it always run with a turbosaver. Does NOT smoke and has NO in and out play. $700 plus shipping
ATI 10inch TH400 convertor. It has gone 9.20s behind a 274 motor with a 76mm turbo. I got it from Ted A. here on the board. It stalls 2700rpm @zero boost, 3000rpm @ 3psi boost and so on. $450 shipped
TH400 transmission - Built by our local race trans builder with an ATI transbrake, ATI aluminum pan, Red Eagle clutches and Kolene steels. It has about <1500 miles on it and zero dragstrip passes. Just street time. Cooler line pressure was verified to be under 35psi. Maybe lower I would have to double check. I just pulled the pan to reseal it (leaking) and the fluid looked good and there was nothing abnormal in the pan. New type F was used. $1000 plus freight.
