T&D GN1 Roller Rockers/Jet Hot GN1 Valvecovers/Vacuum Evacuation

[hemi8]

T&D 1.55 ratio shaft mounted roller rocker system for GN1 14 bolt GN1 aluminum heads, complete with instruction sheet and trend 5/16 dia. push rods. Flawless condition. $450.00 SOLD!
GN1 valve covers, Jet Hot powder coated, professionally welded fittings for breathers and oil fill cap. Breathers connect to electric evacuation pump for a sealed system. Racetronics harness for pump, complete system, simple hook-up. Evacuation pump activates at 3 psi boost. $300.00 for everything, perfect condition.
PayPal is fine, +shipping (lower 48 only)
EVERYTHING SOLD
Mike

 

[jmendlik]

very interested in these......do you take paypal??? Also does the GN-1 Head new from Champion need to be modified to use these? MY heads are on order with Tomn and should be shipping by end of Jan2014. Will these fit under TA Valve covers?

 

[hemi8]

Yes, Paypal is fine. Yes, they will work with your new heads, no modifications at all. Yes, they will fit under the TA valve covers. Paypal address (PM me)
Mike

 

[jmendlik]

Mike-

I'm running the PAC 1203 springs (170 lb seat and 510lb open) and need to verify with Tom @ Champion that these will work. (I will call him on Monday 1-6-14) I did buy the Scorpion 1.65 setup but they have not shipped. I see you had scorpions and switched to T&D...Any issues with the Scorpions??

what length are the pushrods you have?? More than likely these will not work in my application. My block is a virgin stage 1 never decked and the heads are also brand new current run GN-1 Aluminums from Tom. Joe

 

[hemi8]

Yes they will work, they will work with any spring pressure, they are the best roller lifter setup money can buy. Cancel the Scorpion rocker order, you do not want these, even if you don't buy my setup. They tick-tick like hell and have a tendency to come loose, no matter what you do. The shaft mount system is superior in every way.
Mike

 

[hemi8]

Sale Pending on roller rocker setup.
Mike

 

[Soldier_GN]

Next in line if the ro ker sales falls through

Posted from the TurboBuick.Com mobile app

 

[hemi8]

Gotcha, I should know by tomorrow.
Mike

 

[hemi8]

The line for the rockers:
1. Jmendik (Sale Pending)
2. Richard Miller
3. Bison
4. Soldier_GN

Line for the Valvecovers:
1. Richard Miller

 

[Soldier_GN]

Geez...nevermind then...lol...i know if the first 2 dont get Bison will...ohhhh Bison....lol...

Posted from the TurboBuick.Com mobile app

 

[jmendlik]

Mike. .. pm me your PayPal and also the intake pics. .

 

[jmendlik]

Mike-

Paypal payment sent 1-6-2014 for the T&D 1.55 Roller Rockers...

PLz provide tracking number when shipped.

Thanks again
Joe

 

[hemi8]

T&D rollers have been sold.
I will sell the valve covers and evacuation pump w/harness separately.
I am willing to trade my parts in the for sale section for a DLS/Duttwiler external oil setup for stage 2.
Mike

 

[hemi8]

Bump

 

[Eticket]

PM sent on evac pump harness.

 

[hemi8]

Valve covers w/evacuation system still for sale.
Mike

 

[turbodaniel]

Interested in vac pump, just not familiar on how well it works..

did you have it up and running on your car?

If so do you have a pic of install?

 

[hemi8]

The engine and trans were sold a few weeks ago so its off the car. I ran 5/8" heater hose to the breathers, at 3psi boost the dash lights up telling me the pump is on (you can hear it also at low rpm) and it pulls a vacuum helping ring sealing and for me it stopped my nagging oil leak. The crankcase tends to get pressurized when up on boost, you'll see 600.00 Moroso pumps on race cars. There have been quite a few write-up on this board about installing this pump, I set mine next to the evap. canister.

Mike

 

[SirVeyor]

GN1 valve covers, Jet Hot powder coated, professionally welded fittings for breathers and oil fill cap. Breathers connect to electric evacuation pump for a sealed system. Racetronics harness for pump, complete system, simple hook-up. Evacuation pump activates at 3 psi boost. $300.00 for everything, perfect condition.
PayPal is fine, +shipping (lower 48 only)
Mike[/quote]


Mike, do you still have the covers and evacuation pump for sale?

Thanks,

Wayne


Posted from the TurboBuick.Com mobile app

 

[SirVeyor]

Mike,

Sent you a pm.