Search results

Hi, I need a TV cable, Does anyone have a good one for sale? Thanks, Mike

55 pound injectors with 3 TT chips, 93 octane street, alcohol and 108 race chip $300 Hotckis front sway bar $140 12" Kenne Bell lock up convertor with about 15,000 miles $250 Stock zero balance balancer $50 Stock intercooler fan $35 Engine tie down $20 Single gauge A piller pod...

Here is my problem. The TV cable was leaking at the trans case so I went to the dealer and bought a new seal for the cable. I thought it was fixed but the car has been sitting for 4 to 5 days, and there is a puddle under the car almost to the rear axle. This is what it did before, It only leaked...

Siemens 55# injectors with 3 TT chips. 93 octane street chip, Alchol chip and a 108 Race chip. $300 for all New Trans break from Brian $100 Innovate LM-1 with about 200 miles with a new 02 bung $225 Bstc Boost Command $70 12" Kenne Bell torque converter about 15,000 miles $250...

I need the bracket that holds the crank sensor on the timing cover. ASAP, Thanks, Mike

I was wondering what type of fluid to run in the 200R. I was told to run type F in it because of the shift kit. Is this correct or should I use the dextron ll? Thanks, mike

I'am looking for a radio install kit that mounts the radio flush. i have the kit that mounts the radio out, but would like to find a kit that is flush mounted. I know someone makes them because I saw a few cars with them a while ago. Any help would be great. Thanks, Mike

Could someone give me some ideas or pics of were they mounted their Gen 2? I have it wired but I really can't find a good spot. If the wires came out the bottom or back it would look good on the top of the radio(were most scanmasters are), but with the harness sticking out the top it doesn't...

What is the best way to repair a sagging headliner? The liner is out of the car and most of the fabric is falling off of it right now. The board is in good shape. I thought about the 3M spray glue but wasn't sure if it would bleed through the fabric. Thanks for any help. mike

Can you use the upper tubular control arms when doing the 11" S-10 brake swap? I thought I read that there was a difference between them and stock? Any help would be great. I'am talking about the upper control arms that G body parts sells. Thanks, mike

Need a zero balance balancer for a cat crank.

Hi, I need the electrical connectors( plugs) for the TPS and IAC mottor. Also need a good belt tensioner. Thanks Mike

Hi, I'am looking to buy a new turbo and I know someone with a precision turbo but I don't know what size. The exhaust has.83 on it and the comp has AIR 60. Could someone tell me what it is. Thanks, Mike

Any help would be great. I have a set of ESP heads I bought a while back. I'm getting ready to start the rebuild on the engine. Could someone tell me a little info on them good or bad. The vavles have ferrea on the top of the stem. There is seals on both Intake and exhaust. Are they ready for...

Hi, I have a couple of questions, I would like some input for. First I have a T with ATR headers and a TH 3" downpipe. The pipe is warped and won't seal on the turbo. I know you can resuface the flange and use a gasket, but the owner before me made the pipe fit the headers by using a hammer on...

Here is my question. I have a TTA short block with eastern performance heads. The car has been sitting for a year or so. I did a compression test on it and the numbers range from 163-170, is this to high? I know there is a differnce in the pistons on the TTA and GN Short blocks. These numbers...

Here's the questions. I have a TA short block in my car now, with ESP heads. The engine has always seemed to have a lot of blow by out the breathers. I found that someone had put a ground down bolt in the hose between the PVC and dog house. Could this cause alot of blow by. Second Are the cranks...

Thanks Rob, great guy to deal with.

Question is whats the difference between a door panel from a power window car to a manual crank car. I need a new driver upper door panel for my car but it is a manual crank and I can get a nice one from a power window car but are the holes for the crank and switch in the same location. Thanks, Mike

I bought a used PTE front mount intercooler, my question is do you have to use a blowoff valve. What are some off the advantages or disadvantages of using one, driveability, etc. Thanks.