Search results

I need a new turbine wheel for a PT53 turbo. Precision will no longer sell me turbo parts. I did a search on the internet and it seems like I am dealing with deep voodo magic and there are few to none offering turbo parts for sale. I have a place close by that will do the balancing for me...

I was reading another thread and someone mentioned that it would be better if we would raise the compression of a motor and make it more E85 specific. I am in the process of gathering parts for my TTA and will be setting it up to run on E85. I am going to pull the motor to look for a knock. A...

I picked up a GTA Trans Am for misc. parts. It was a 350 TPI car. From what I remember reading in order to put a Turbo V6 in the car the K member has to be changed. Do I remember correctly?

I was wondering if anyone knew if the T-Top weatherstripping/trim is still available from GM. I do not really need the weatherstripping where the side window meets the T-Top. What I need is the harder rubber/plastic trim that covers the weatherstripping. The part that you see when looking at the...

Can anyone identify these injectors? 01D030B? They also have these numbers on them 0797. I tried to search the site but I did not get any results.:confused: Jeasen

The airline mechanics were working on the airplane I was on. We were waiting at the gate while they preformed their magic. It so happened that I was in the window seat and I looked down at the golf cart that they used to transport their tools to the airplane and low and behold the back of the...

I am trying to change the torque converter on my 1989 Turbo Trans Am. I have the transmission out of the car and can not get the torque converter off the transmission. I have changed several turbo Buick torque converters in the past and they have always pulled right off the transmission. The...

I have the transmission out of the car and can not get the torque converter off the transmission. I have changed several turbo Buick torque converters in the past and they have always pulled right off the transmission. The tag on my transmission says TA F and the torque converter has the number...

I have a TA49 Turbo that I want to install on my TTA. The wastegate hole has been ported on the Precision AR 63 exhaust housing. I know that I can use a plate to block off the larger ported waste gate hole and get by using the standard puck but I also know that the wastegate hole was ported to...

I just purchased a Razor Alky kit from a board member for my TTA. Although I received a full set of instructions I still could use some help installing the Alky kit on my car. I would really appreciate pictures. They would really help me understand what is written in the instructions. The...

My TTA develops a knock when the motor gets to operating temperature. When cold no knock but it does not run as smooth as I think it should. It runs rough when cold and is worse when hot. I had some very knowledgeable Buick V6 guys listen to the motor when cold and then to the knock as it warmed...

Anybody have an exhaust housing laying around for a TA49 turbo that does not have the wastegate hole ported? Want to part with it? If so send A/R and price. Thanks.

Just put the Direct Scan on the TTA and was wondering if the MAF reading was right. At WOT the MAF reading increased as the RPM's went up but the highest reading at 5000 RPMs was 195 g/s. Is someone is using a translator & LS1 MAF on their TTA? Could you check a Direct Scan file and see if my...

Anyone have an ATR 2 1/2" downpipe laying around that they would like to get rid of? I am thinking that I could use one. Anyone??

I am going to be upgrading the fuel pump and adding a hot wire kit to the TTA this week end, therefore I will be removing the gas tank and panhard bar or rod. I know there are heavier aftermarket panhard bars available for our cars. Does anyone have a factory panhard bar that they boxed? If so...

I am looking at a set of 15X8 wheels for the front of my car, and a set of 15x10's for the rear. The 15x8's have 3.5" back spacing and the rear 15x10's have 4.5" back spacing does this sound like an allright fit. From what ive seen from previous post the 15x10's will be allright but I don't know...

Well I returned to Kansas City last Saturday night wondering all the way back why a Buick sponsored event would run a Pro Tree. I talked to several people since I have been back in Kansas City and voiced my concern many times. I just could not understand why the Pro Tree? It was almost like we...

Just wondering if there is a Buick vrs. Mustang Shoot-Out scheduled for this year??? :confused:

Does anyone have a copy of a a/c wiring diagram besides the one that is on gnttype.org? I need one that is a little more legible, so I can print it.

Anyone using the ATR Down Pipe? If so how did it fit? Did you have any problems with the installation? I am going to start modifying a stock TTA and this seems like a good place to start. Jeasen