Recent content by DOG
Welcome!
By registering with us, you'll be able to discuss, share and private message with other members of our community.
-
D
Relay replacement part #?
Hello all, I was having a problem getting fuel pressure to my engine prior to starting and discovered that the fuel pump relay had a burnt plug. I purchased the car with the hot wire kit upgrade already installed so i am not sure if its racetronix or caspers piece. i was told it was a bosh...- DOG
- Thread
- Replies: 2
- Forum: Engine Tech
-
D
Ignition problem key stuck
Grabbing the column and turning to the Left worked like a champ. Thank you all, but why did it do this and can someone go into detail on how to fix it?- DOG
- Post #8
- Forum: General Turbo Buick Tech
-
D
Ignition problem key stuck
Well after a day of riding around town i parked at home in the garage and shut her down, however i cant retrieve the key from the ignition. The ignition will not pull all the way back to the off position but i was able to kill the engine. Now i cant start the car or remove the key from the...- DOG
- Thread
- Replies: 9
- Forum: General Turbo Buick Tech
-
D
Fuel Pressure Regulator?
Sorry to piggy back on this thread but i am having the same start issue. (new battery, alternator, charging system good and intact) Sometimes i don't get any fuel pressure to the engine, but other times it cranks up with no problem. Its a crap shoot every time i decide to go out for the day...- DOG
- Post #13
- Forum: General Turbo Buick Tech
-
D
86 87 gn wheel rim
Im still learning how to navigate the forum /website and i was looking to refurbish my rims. I was scrolling through the wheels section and came across the work you recently did and I would like to give you a call. I will try the PM thing first if i can find it. Those wheels look awesome!- DOG
- Post #3
- Forum: Parts wanted
-
D
ready for refurbished wheels (OG lug nuts)
thank you- DOG
- Post #16
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
Tips for replacing backing plate
The stupid O clamp with wings, that secured the wheel cylinder was the worst part of this whole project. I ended up removing the backing plate and using 2 screw drivers to push it flush (evenly) then my buddy to another screw driver with a small hammer and we finally secured it. We put...- DOG
- Post #12
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
ready for refurbished wheels (OG lug nuts)
Where can I send my wheels to come back looking like this? I'm down in south Fl and how much would I be looking at?- DOG
- Post #14
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
Tips for replacing backing plate
Well i compared my original wheel cylinders to the S10 wheel cylinders, and i discovered that the bigger ones would not fit right in place. The bigger ones had two additional screw hole adapters (no idea where that would go) and the bracket on the back was not identical to the OEM. I...- DOG
- Post #9
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
Tips for replacing backing plate
No i just went with OEM replacements from the auto part store, i could probably return them but what would i be looking for? I successfully accomplished to remove the axle and backing plate, but I am having trouble removing the parking brake from the backing plate (any recommendations). I...- DOG
- Post #4
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
Tips for replacing backing plate
Hello all, I ran into a problem after converting my 87 GN from the powermaster brake system over to a vacuum system. As i was bleeding the rear drums the wheel cylinder busted. Then I attempted to remove the wheel cylinder without knowledge of the clamp holding it on the back of the backing...- DOG
- Thread
- Replies: 11
- Forum: Brakes, Suspensions, Tires & Wheels
-
D
Possible ground wire for gauges?
I have been bitten by the electrical gremlins all of a sudden. In my 87 GN I looked at my Oil pressure/Water temperature gauges were reading 0's. Immediately I stopped the car and checked my fluids which were all normal. Then I noticed this little White wire with a bad terminal was barely...- DOG
- Thread
- Replies: 2
- Forum: Electrical & Wiring
-
D
Not sure how to send a PM but we should schedule a day to meet up.
Not sure how to send a PM but we should schedule a day to meet up.- DOG
- Profile post
-
D
All Florida Turbo Regal/TTA Owners Sign in here
Checking in from the Lee County / Fort Myers area. Also having problems prioritizing what project to tackle first and finding a trustworthy source closer than Tampa.- DOG
- Post #433
- Forum: Florida Area
