1986 modified monster parts


86 vader
Jan 19, 2010
Parting out my 1986 GN. WE2 code locking TTops. Here's what I've done to it over the years
Poston Enterprises motor mounts
Eagle forged crank
Poston bearings
Reconditioned stock rods
TRW forged pistons bored 30 over
Kirban oil pump
Comp Cams hydraulic
roller cam kit # 69 300 8
Comp cams magnum push rods
Stock heads ported
Postons chrome moly valves,
Bronze valve guides and
Nickel valve seats
Cometics MLS head gaskets
T&D shaft roller rockers
GN1 valve covers
ATR 3inch down pipe
GN1 competition only headers
Block Balanced and Blueprinted
Accel 30LBS. injectors
Kirban adjustable fuel press regulator
RJC power plate
Billet vacuum block
Turbo XS blow off valve
Polished intake pipe
Torque strap
K&N cold air intake with 4inch 90°elbow
Chrome turbo inlet pipe
TE 62 Turbo
Kirban stock appearing
adjustable waste gate
GBody Performance stock loc.ext.intercooler
GBody Performance dual fans
Kirban stock radiator
Kirban hot wire fuelpump kit
Walbro HO 255 in tank fuel pump
The Rooster Amp Booster
GBody Performance trans cooler
Rebuilt Stock Transmission
Includes 2400 stall 12inch
Lockup torque converter
Billet stator support
Master rebuild kit
Performance shift kit
Red diamond clutches
Performance valve body kit
New servo
☆Less than 500 miles on car
since rebuild!!
Energy Suspension body bushings
Hotchkiss upper and lower
Control arms rear end
Grand National posi G80 code
Stock interior fair condition
I used a 65 Mustang
Polished Aluminum T shifter
Handle. Looks and performs better
Than the plastic GM part
Replacement bumper fillers
Front are good condition
Rear damaged but can be repaired

I have a few after market gauges
VDO boost, VDO oil press,
Autometer air/fuel gauge
and fuel press. gauge and
water temp°gauge.
Netami RPM gauge customized
For the Grand National by removing
Manual transmission shift light and mounting tab, wetsanded and color matched to GN grey interior
I have 4 18×9 inch aluminum aftermarket wheels with 3 inch polished lip new Pirelli P Zero tires and 1/4 inch spacer on the rear. I'm not sure what company made the wheels but they are in good shape but could use a paint job.
I have a clean title and willing to sell car whole or parts. The carpet is in good shape I replaced the weather stripping on the whole car about 5 years ago
The front seats reupholstered but the driver seat power motor not working.
The car was in 1 accident before I bought it the driver rear quarter replaced so with the right body shop she can come back to life oh the rear floors are rusted and need to be replaced.
I have almost $30 Grand invested but my loss can be your gain at $8 grand. I'm not selling for less than that for whole vehicle so no disrespect but please dont ask. Again this car is available whole or in part

I do have some extra parts like stock turbo intercooler pushrod turbo heat shield TTops ATR manual boost controller steering column lock. Call for any pics.or details. 703 371 5341 ask for Darien


  • 06b0addc80fd7d812b50711a192224ec.jpeg
    11.8 KB · Views: 101
  • 20190608_103850.jpg
    5.1 MB · Views: 104
  • 20190608_104031.jpg
    3.1 MB · Views: 93
How much for the steering column lock to 60101? The roller cam is installed in engine?
I'll need the t tops an that 87 grill if parting it out starts.

Sent from my SM-G930T using Tapatalk
radiator and fans installed on car?
Trans cooler?

Pics and priced shipped for each
Thank you dagwud for the response, somethings came up so I’m going to have to pass. But, that’s a pretty good deal glws.
Roller cam is in engine column lock $50
Sorry I didnt get back with you. I will take the column lock. I would take the cam kit but its going to be easier for you to sell engine with it lol. Do you have paypal? Total shipped to 60101