Those running Kirban's full billet fuel regulator, need a favor

[TR Custom Parts]

Need to know how much the stud that controls the pressure setting measures from the top of the lock nut to the end of the stud. Not one out of the box but installed on the car with fuel pressure set.

Also, anyone know what size or part number for the o-ring that goes to the return line? NOT the one that goes to the fuel rail!

Thanks

 

[trbojo]

i would have to go measure the stud, and not sure of the oring size, but you can get an assorted pack of them in the help section at auto zone.....

 

[TR Custom Parts]

Grabbed the assorted pack from Advance and no go, not the right size for the return.

 

[trbojo]

Grabbed the assorted pack from Advance and no go, not the right size for the return.

i used az's with no problem....i'll see if i can find the container with p/n....

 

[TR Custom Parts]

Cool, appreciate it. also the measurement of that stud would be helpful. Will post in a different thread what I am up to. Picture shows the oring I took off on the left and the one from Advance on the right. It will fit in the housing of the regulator but is not snug on the line itself.

 

[trbojo]

help p/n 80020 viton oring kit...i used them on feed and return no problems....i'll check the stud tomorrow if i get a chance....i'll prolly be in touch with you in a few weeks for a maf pipe and maybe a few other things.

 

[ttaowner]

i bought 1 last year from the napa in the parking lot of my shop last year and it worked like a charm. i dont believe the people up there are geniuses either so you should probably have just as good luck at your local napa. i brought my old one in with me.

call me tomorrow evening if you can to mark to discuss something we were talking about on the pike a couple weeks ago. thanks

 

[TRICKSIXPA]

Napa Part# 730-4912 the package contains both O rings for the fuel lines.

 

[Boost231]

if no one post the length i will tonight when i get home

 

[TR Custom Parts]

Got the orings, Pep Boys had the Help kit.

Reason I am asking for the stud height is that I put a plug in the top and concerned that the disc inside the regulator is going to bottom out on it. I am tapping off the side of the regulator for the boost reference line instead of off the top.

 

[Boost231]

mark, i have a modded top i could have sent you so you could use the air brake fittings. it was drilled and tapped and still clears the stud.

 

[trbojo]

Got the orings, Pep Boys had the Help kit.

Reason I am asking for the stud height is that I put a plug in the top and concerned that the disc inside the regulator is going to bottom out on it. I am tapping off the side of the regulator for the boost reference line instead of off the top.

was it the p/n i sent? curious if i pulled the right box out! lol...too many spare parts laying around for this thing....

 

[TR Custom Parts]

P/N was correct, thanks.

Here is what I need measured. Anyone???

 

[trbojo]

7/16"......

 

[Boost231]

.485 on my mic.

 

[TR Custom Parts]

Thanks, I should be all set.

Here is what I was doing........... http://www.turbobuick.com/forums/th...-billet-vacuum-block-how-i-plumbed-it.380004/

 

[SS/GN]

Mark I think you have tooooo much time on your hands.I really think you need more hobbiesNice work

Kevin

 

[TR Custom Parts]

Mark I think you have tooooo much time on your hands.I really think you need more hobbiesNice work

Kevin

Need people to place more orders so I don't have any spare time.

 

[Phoff]

If you need a couple O rings let me know and I'll drop a couiple in the mail for you.

Pete

 

[TR Custom Parts]

Thanks for the offer Pete, I am all set, found some.