Recent content by jess70502

  1. jess70502

    Holley HP EFI + Cruz Harness Install

    I am very excited about this. So close on pulling the trigger. In my opinion it’s a bargain really. Let’s compare it to the gn-Ecu; with this setup you get a entire brand new harness, 6 coils and brackets, new sensors and I’m sure there are a couple more things. Even though it’s not quite an...
  2. jess70502

    What are good base line parameters for SD2 on E85?

    Hello all, Lets start from the beginning. Switched over to SD2 and I'm a little overwhelmed. I guess I don't know what my target air fuel ratio is suppose to be at WOT, idle, cruise etc. etc. I have my wideband setup to show in lambda scale. It just makes it easier I think. I also realize every...
  3. jess70502

    Suggestions on specing out a motor build

    That's about what I get from it, I've got time. The car runs good now I'm just planning for the future
  4. jess70502

    Suggestions on specing out a motor build

    My main question is what's the latest lingo on turbos, I have my eye set on the 6466 cea but I like to know which cam and torque converter to go with it. Which heads are better gn1s or ta's
  5. jess70502

    Suggestions on specing out a motor build

    Well that's what I kinda mean, I'd like to have a strong foundation then once and a while go the track and turn it up but not to its limits though. A few guys around here have some nice motors and they don't have really anything too crazy done
  6. jess70502

    Suggestions on specing out a motor build

    More power the better! Honestly somewhere around 800hp would be the goal. I was definitely going to go girdled. I noticed precision came out with a new(ish) line of turbos. I'm eyeing the 6466 CEA. I did a search on here and didn't find much info on it. But I guess I'm just worried about the...
  7. jess70502

    Suggestions on specing out a motor build

    Hey guys I'm looking for suggestions on a motor build. I'm probably going to go with ta intimidator heads and champion intake. I already have a built 200r4, -8 feed -6 return on e85 running a single 430. Will probably upgrade that to a double 340 with a Hobbs switch. Also have a presison front...
  8. jess70502

    Info on GTA wheels

    forgot the link, http://www.hawksthirdgenparts.com/gta-mesh-wheel-set-of-4-17-x-9-black-reproduction/
  9. jess70502

    Info on GTA wheels

    Here is some on Hawks Third Gen. 17"x9" My current setup is 16"x8"s all around. Here is my question. Would it work and look good if I ordered the set and went with 275 tire or 285 tire two with street tires and two with drag tires? Would that staggered setup look ok? 16s up front and 17s out back?
  10. jess70502

    Powerlogger file review

    Autometer 5778
  11. jess70502

    Powerlogger file review

    6.1 tt chip, e85, ported irons and intake, front mount intake, unknown precision turbo Posted from the TurboBuick.Com mobile app
  12. jess70502

    Powerlogger file review

    Hey guys, I'm pretty new to Powerlogger so I finally made some runs and I kinda want a second look at things to make sure everything is ok and good to go. I noticed that my tps voltage at WOT isn't where it should be (maybe I need to take out the floor mat). Any help would be greatly...
  13. jess70502

    Best dual fan setup with be cool rad

    It's one of the best things I've put on the car to date, it never gets over 180 in vegas with the ac on Posted from the TurboBuick.Com mobile app
  14. jess70502

    Best dual fan setup with be cool rad

    I went to the exhaust shop and had them bend me 3 inch tubing 2 bends at 45 degrees and 2 at 90 degrees. About an hour later and a lot of cutting and welding this is what I got. Posted from the TurboBuick.Com mobile app
Top Bottom