Turbo Buick Parts, Performance & Stock

[turbocliff]

Here's what I've got:

Precision Front Mount IC : Needs new 3" auminum tubing from turbo to IC inlet, other tube has small dent at the bottom: $600.00

Clean, Standard bore 109 block: $150.00

Hooker Headers for 86-87 GN : $250.00

Stock Radiator from 87 GN: $50.00

Factory wiring harness for 87 GN: $best offer

Ported upper intake plenum: $35.00

Factory 87 GN cam sensor : $100.00

ATR Aluminum Drive shaft for GN: $250.00

Factory GN gas tank: $50.00

Have quite a few other parts, lemme know what you're lookin for, I may have it-

All pricing does not include shipping-

Cliff

 

[Intercooled88s]

I'm interested in the 109 block, how much shipped to 01056. I would like to be first in line for it. My e mail is Fortune628@aol.com


Clean, Standard bore 109 block: $150.00

 

[fatride]

2nd in line for the block, I'm in Glendale HTS as well. Also what kind of condition is the gas tank in???? Turbocliff, I see your moving back to the area

 

[DR BOOST]

ill call u about the driveshaft. do you think it is strong enough for my 12 sec car?

 

[turbocliff]

Dr. Boost- I'm sure this drive shaft would make a nice addition to your car, but then I would need the hit when we race again...

 

[Boostmeister]

Hi,

I am interested in the rad. Please describe the condition and shipping amt to 18015.

Thanks

 

[my 1st gn]

radiator

would like to be next inline thank you

 

[turbocliff]

intercooledss- Gonna sell the block local, but thanks for your interest. Couldn't find shipping for less than $100

fatride- pm sent, see you friday!

Dr. Boost- Would you like to grab a lane?

Boostmeister- The rad is in good condition, normal small dents and bent fins at the surface of the core. but no leaks, no patches, never filled with stop leak or anything like that. Shipping would be $28.00

my 1st gn - well your next in line, but what would you like?

cliff

 

[Under Pressure]

yes

i need a couple to dr.boost

 

[Boostmeister]

turbocliff, sent you an email.

 

[DR BOOST]

sorry cliff....you have been banned from the people's champion competition. but id be more than happy to to give you an exhibition run.

i thought you would have learned by now...dont get the gorilla angry.


under pressure...are you calling me out?

 

[WIKEDV6]

I’ve heard that the Pink Bunny is growing two extra whiskers and the Gorilla is getting King Kong’s testicles. I will be sitting and watching this year again as usual. Can the whiskers made of titanium pierce through King Kong testicles or the King Kong testicles just going to run over the Pink Bunny?????


Later
Prasad

 

[Boostmeister]

Turbocliff - you still out there?

 

[turbocliff]

Boostmeister - Email sent my friend.

Also, if anyone is interested, I still have the following:

ATR Aluminum Drive Shaft
Precision Front Mount (needs piping)

Cliff

 

[turbocliff]

Precision Front mount still available, make offers!

I do have the piping for it, and the aluminum pipe from the IC to the throttle body is fine, just the pipe from the turbo to the IC could be replaced for aesthetic reasons, but it worked well enough for me to go 10.60s @ 30+psi on my GN...

Cliff

 

[Hot Air]

Do you have an under dash wiring harness for sale?
Conrad Carter

 

[bttwracing86T]

still have the headers

hey you still got the headers and if so why are you getting rid of them and how do they compare to the others for quality and performance.

 

[chris2316]

cliff, was that in a 79 regal?

 

[turbocliff]

cliff, was that in a 79 regal?

Most of the parts (which are now sold) did come from a 79 Regal that I bought with an 87 GN Drivetrain, but the numbers I ran were in my 87 GN

bttwracing: I do still have the Hooker Headers, they obviously out perform the stock headers, but probably do not have the same performance increase as the ATR headers. I never ran either on any of my GNs, personally I think aftermarket headers are a waste of money on any turbo buick unless you are going low 10s or faster. But if you have cracked manifolds or something, they are certainly less expensive than finding new factory parts-

Cliff

 

[Hot Air]

Do you still have the 79 Regal? If so, are you parting it out? I'm looking for power window motors and regulators from a 79-80 Regal.
Conrad