Search results

Does any one know what are the troque number for the bolts on the rear end housing. Its started to leak and I will be putting in a new gasket and oil.

I have a few parts that are taking up space. 1. a stock intercooler with the dutt. neck mod on it. $200.00 2. poston`s driver side replacment header. make offer. 3. poston`s cross over. $70.00 4. aftermaket body bushings with the gnx ones. $80.00 5. caspers volt booster $45.00 6...

I have a set in good condition. I am asking 70.00 shipped to your door. e-mail me for pics or any infor. mfastkidd@aol.com

I have just gotten a manual boost controller, but i didnt get any instructions. Can anyone tell me how to hook it up.

I am going to install the cam sensor. I understand everything, but the 1.45 in. what is that in inches. is it 1. 1/4 or something else. I need the actuall, so that I can get a mess, tape out and mark it up on the balancer. does any one kown.

Does any kown the bolt size for the tensinor on the timing chain. I am going to be doing the cam and the last time I went in to replace the front cover I saw that it had a double roller and now I will be going back to a single style chain.

I have a pair of the clear parking lights. They are 8 out of ten. I would take $65.00 shipped for them. If interseted in them let me know. My e-mail is mfastkidd@aol.com

were can I find a new pcv hose. Do the auto parts store carry them because I need to find one asap. THanks.

I replaced the stock timing cover and now I need help with the crank sensor. Does the sensor go on with two sturds or is it just one. The porblem is that I only put one sturd on which is the bottom one. I cannot get the sensor to sit fush. THe balancer blades will hit the sensor blacket. So now...

How do you konw if you have a double roller or not. How would it look compare to a stock steel timing set. Would the timing chain be tight with little to no play or would it have a lot of play. I am asking because I just changed the front cover on my car and it had a replacement timing set, but...

Today I was chaning the timing cover and I broke one of the screws. Its the one that holds the timing tab for the blancer. Does anyone know the size of it.

Does anyone know what years if any cars have the same timing cover as the 87 gn.

I am going to install a cam in my car, but I dont have the time to do it in a weekend. I will be doing little by little over the week and then on sunday hopfuly be done by then start to fire it up. My question is can I leve the engine open, with the mailfod and timing cover off with nothing...

I need to know what can I use to prime the oil pump. I have the cam sensor off and what do I use? I have read some were how to do it, but I dont know what tool I need. Can some one please help me out. Thanks.

How hard is it to install a cam in a 87. I have read the insturtions on gnttype.org, but I want to make sure it is not to hard. If any one can give me any tips to make it a alittle easyer please do so.

I have a question. Its how do you wire up the floating device that goes in the tank. I am going to make my own and I plan on puting an led to light up when the pump turns on in the dash were the power injection is. Now I what to put other led in the dash also so when the alky is low it will turn...

I have a question on cams. I have a chance to get a 214/214 with a lift of 440/440, the rocker ratio is 1.500. It says it is for a small block dodge, would this cam fit in a gn. I have hear that everyone gets a cam for a small block chevy. Do i need to worry about the duration, lobe, and lift...

Does anyone know were the ground for the fan is, not the one on the fan or wire, but the wire were does it get the ground to. My fan is not working and the relays are all good. I have checked for power and it is there. There is no power at the there wires that cennet to the fan, when it needs...

Does anyone know what the size of the bolts for the turbo heat shield are. I have lost them and I am now after a year going to put it back on.

I am about to put new pads on the car and my two choices are carbon or seim-mat. which are the better ones. I have headed some thing about the seim-mat, that they hurt the rotors, but I dont know.