Stage 2 built. 1987 Buick Turbo T - project -"Fall out "

[TURBOTERRORV6]

Thanks to Steve else for this nice 70 mm accufad

 

[TURBOTERRORV6]

Antonio stojabov for this white racing modified timing cover with a modified external oil pump .

 

[TURBOTERRORV6]

Thanks to Atlas chrome in Houston Tx for the polishing work of the BGC fuel rails.

 

[TURBOTERRORV6]

Thank again to Antonio S. For another piece of the bottom end for the stage 1 012 block.

Here is a BHJ internal balancer

 

[TURBOTERRORV6]

Got distracted a little on the engine parts for the S1 built

Here is one rare piece made my KB , a one piece air damn that was introduced in the mid 90s. Jpolzin had this stored for a while and I had to convince him to sale it to me ! This will be a great addition to project fall out.

I will have to modify the center scoop in other T for the cold pipes to make w

 

[TURBOTERRORV6]

Again , thanks to Jpolzin for this brand new full set of RJZ razor pulleys for the stage 1 built.

 

[TURBOTERRORV6]

just a little brief write up on the whole parts as j still have a lot of updates to load up here.

The built will consist of a stage 1 012 block that was purchases in the north eastern part of the states and delivered to Houston tx

The heads will be a fully race Ported M&A revised aluminum head castings with over size valves and beehive springs. They will be equipped with scorpion style 1.7 rockers.

The intake as you may know is a early casting BGC off center that will be race ported as well and powdercoated in a un traditional coating. (Valve covers as well ).

The porting and polishing are being worked on by panhandle racing out in Amarillo Tx.

The 012 block will also be machined to a 262ci with BMS Buick Motorsport internals.

This setup will be run with E85 fuel system.

More to come ..

 

[TURBOTERRORV6]

Thanks to Chris Marin out of El Paso Tx for this great set of M&A heads.

These heads came complete including a set of valve covers , pushrod and stud mount arp bolts.

These were picked up initially in February of 2016.

 

[TURBOTERRORV6]

A pic of the passenger side mirror.

 

[TURBOTERRORV6]

Some
Parts for the external oil pump ... These parts were from white racing and marine .

 

[TURBOTERRORV6]

Back to the exterior of the turbo T. The passenger inner plastic well on the car was busted on the lower end of the well .. It took me 4 months just to find a good condition passenger inner well ! . Thanks to Robert wells out of Dells, Wisconsin he delivered as promised. A well conditioned part !

 

[TURBOTERRORV6]

The fenders were installed just recently. Next up is the installation of the passenger wheel well , and rhino coat all inner plastic wells. The factory turbo T wheels will be replaced with a set of 17" simmon wheels .

 

[TURBOTERRORV6]

The arrival of a surprise.

Thanks to Robert aka AlaskaGN out of Alaska, USA for these amazing wheels.

17" simmon wheels with new BFG tires !

 

[TURBOTERRORV6]

Another close up shot for these Australian made exotic wheels.

 

[TURBOTERRORV6]

I will
Post more pics in upcoming days.

Thanks for viewing.

 

[Nyoricanone]

Now in the process of the paint and prep of project fall out. I've picked up some parts for the stage Q built along the way.


Thanks to members of the community and private collectors

hey do u know where I can get a complete front bumper for a gn?

 

[TURBOTERRORV6]

For mock up purposes only. The pan is obviously a deep one and has a baffle insert including a low profile pick up unit.

Stage 2 block 012

 

[278cikiller]

View attachment 278574 View attachment 278572 View attachment 278571
Thanks to Richard Moore from Houston tx for this new GN1 3 " dual true SS exhaust.

Were did you get this Exhaust system, I don't what the tail pipes if that possible. LMK thank's

 

[WIKEDV6]

Subscribed!

 

[TURBOTERRORV6]

After two sand blasting trips to strip two coats of black paint. Baked at 375 degrees of off traffic white coatings... This is the results ...