All these parts went 9's with a 67 turbo on my 93/alky motor. I went to aluminum heads with a race manifold so the following is for sale. All parts have a dozen or so track passes and maybe 1000 street miles except for the heads which have 3 passes and a few hundred miles since Bison set them up. Paypal +3%, shipped items are to the lower 48.
Champion Irons...modified by Bison with PAC-1203 springs with titanium retainers, locks, viton valve seals. Springs are installed at 1.75-1.76" height with 170lbs on the seat...open pressure should be around 520ish so limited travel or solid lifters are preferred. I was .050-.060 from theoretical coil bind at .587 lift.
SOLD
![IMG_7153.jpg IMG_7153.jpg](https://turbobuick-data.community.forum/attachments/194/194782-cef20cc347af598c9735d433e192f4ba.jpg)
Champion Ported stock intake- drilled and tapped for vacuum fittings at the back of the manifold, you can always plug these if using the stock vacuum routing. 3/8 npt for the iat sensor, 1/4npt for the brake booster and 1/8' npt for a pushlock fitting. There is also another 1/8" npt tap in the front that i used for my regulator. Includes the EGR blockoff plate.
SOLD
![IMG_7145.jpg IMG_7145.jpg](https://turbobuick-data.community.forum/attachments/194/194786-c7ccbe77edb32bda51779d672796aad1.jpg)
Champion Fuel Rails- for a stock manifold, used on the one above...setup for an external bypass regulator, includes mounting brackets but no fittings.
SOLD
![IMG_7147.jpg IMG_7147.jpg](https://turbobuick-data.community.forum/attachments/194/194789-b1dd0225819445a881cc8541267248b2.jpg)
Precision Polished 70mm Plenum- drilled and tapped on the side for 3/8npt where i ran my pcv hose into, or you can use it for iat which is the same thing.
SOLD
1/2" plenum spacer
SOLD
T&D 1.55 Roller Rockers- for iron heads... all hardware included.
$525 shipped
![IMG_7156.jpg IMG_7156.jpg](https://turbobuick-data.community.forum/attachments/194/194788-c05020aa1f972836281588414fedce86.jpg)
ARP 12pt head studs- for iron heads, all washers and nuts included
SOLD
![IMG_7154.jpg IMG_7154.jpg](https://turbobuick-data.community.forum/attachments/194/194790-0af1356c4c983619a605b86e8e275b2c.jpg)
Champion Irons...modified by Bison with PAC-1203 springs with titanium retainers, locks, viton valve seals. Springs are installed at 1.75-1.76" height with 170lbs on the seat...open pressure should be around 520ish so limited travel or solid lifters are preferred. I was .050-.060 from theoretical coil bind at .587 lift.
SOLD
![IMG_7152.jpg IMG_7152.jpg](https://turbobuick-data.community.forum/attachments/194/194781-5510e05aa316221df6dfa956d88c9c61.jpg)
![IMG_7153.jpg IMG_7153.jpg](https://turbobuick-data.community.forum/attachments/194/194782-cef20cc347af598c9735d433e192f4ba.jpg)
Champion Ported stock intake- drilled and tapped for vacuum fittings at the back of the manifold, you can always plug these if using the stock vacuum routing. 3/8 npt for the iat sensor, 1/4npt for the brake booster and 1/8' npt for a pushlock fitting. There is also another 1/8" npt tap in the front that i used for my regulator. Includes the EGR blockoff plate.
SOLD
![IMG_7142.jpg IMG_7142.jpg](https://turbobuick-data.community.forum/attachments/194/194783-46d4841e4dc8a4e8f3d61467400b930e.jpg)
![IMG_7143.jpg IMG_7143.jpg](https://turbobuick-data.community.forum/attachments/194/194784-2cd1ec2db25a9ade37d5cdf0df4d6727.jpg)
![IMG_7144.jpg IMG_7144.jpg](https://turbobuick-data.community.forum/attachments/194/194785-11bfdde80d44064328c8f4acf4369393.jpg)
![IMG_7145.jpg IMG_7145.jpg](https://turbobuick-data.community.forum/attachments/194/194786-c7ccbe77edb32bda51779d672796aad1.jpg)
Champion Fuel Rails- for a stock manifold, used on the one above...setup for an external bypass regulator, includes mounting brackets but no fittings.
SOLD
![IMG_7147.jpg IMG_7147.jpg](https://turbobuick-data.community.forum/attachments/194/194789-b1dd0225819445a881cc8541267248b2.jpg)
Precision Polished 70mm Plenum- drilled and tapped on the side for 3/8npt where i ran my pcv hose into, or you can use it for iat which is the same thing.
SOLD
1/2" plenum spacer
SOLD
T&D 1.55 Roller Rockers- for iron heads... all hardware included.
$525 shipped
![IMG_7155.jpg IMG_7155.jpg](https://turbobuick-data.community.forum/attachments/194/194787-12f1ed1ba7e948854a68e0f91244e343.jpg)
![IMG_7156.jpg IMG_7156.jpg](https://turbobuick-data.community.forum/attachments/194/194788-c05020aa1f972836281588414fedce86.jpg)
ARP 12pt head studs- for iron heads, all washers and nuts included
SOLD
![IMG_7154.jpg IMG_7154.jpg](https://turbobuick-data.community.forum/attachments/194/194790-0af1356c4c983619a605b86e8e275b2c.jpg)
Last edited: