Need some help with info on turbo...

[turbox-tech]

Purchased a complete engine with built internals and all the goodies. The turbo on it was what I thought was a TE-44 but there is no name markings on it. The seller who I trust told me it was purchased from a turbo buick vendor about 3 years ago and only has about 4,000KM on it. The turbo has ZERO shaft play and is excellent shape. It came with a internal gate with the external gate option on the turbine and has a .63a/r exhaust and the only # I can find is on the compressor housing (#671381). I did a google search with no luck but a bunch of BS. ANY HELP WOULD BE APPRECIATED!
thanks

 

[Squid4life]

Post a pic?

 

[Squid4life]

trying to find a pic of mine, but I think it is on my other PC...

 

[turbox-tech]

if I send you the pic can you post it for me ..not sure how to?

 

[Squid4life]

If you look at this thread, look toward the bottom right. Says "POST REPLY / UPLOAD A FILE / MORE OPTIONS". Click "UPLOAD A FILE", find the file on your 'puter, and upload it. If it doesn't work def send it to me and I will post it.

 

[turbox-tech]

thanks
just letting the camera charge up!

 

[bison]

take off the compressor housing and post the diameter of the large and small sections of the compressor wheel. Post a pic of the turbine also. It may be hard to remove the ex housing but i can probably id it wiht a pic. Anything else without pics or measurements is guessing

 

[turbox-tech]

compressor is a .50 a/r in the snout (outlet) of the compressor. I will do the ind. and exd. of both compressor and turbine tomorrow as I will have to heat the turbine bolts . CHRA looks to be a Garrett section but I can not make out the casting marks (rust/heat)

 

[jasjamz]

look for te 44 scribed around the compressor outlet

 

[turbox-tech]

no TE-44... can someone upload these pics. I can not downsize them or get my program up to downsize!

 

[turbox-tech]

took off the compressor...looks like 56-57mm ind. and 76-77mm exd....i'll work on the turbine side tomorrow or Saturday. Thanks for all the input gang!

 

[turbox-tech]

Anyone help me with the above numbers and post some pics ? Also, I'm not going to chance taking off the turbine as the bolts will likely snap in the housing.

 

[John Wilde]

http://www.precisionturbo.net/turbo...s/details/Entry-Level-Turbocharger---4431E/60



Entry Level Turbocharger - 4431E

​

Part Number: PTB003-4431

Manufacturer: Precision Turbo and Engine

MSRP: $599.99

HP Rating: 565​

Are you trying to put together a cost effective turbocharger system for your vehicle? Well, we've got just what you're looking for! Precision Turbo and Engine's line of Entry Level Turbochargers provide the perfect solution by delivering a high-quality turbo at a budget-friendly price.

This Entry Level unit features the following:
• 58mm inducer compressor wheel
• "E" compressor cover 3.0" inlet/2.0" outlet
• 57mm exducer T31, 76 trim turbine wheel
• Turbine housing options:
- Buick .63 A/R
- T3 .48 or .63 A/R with 4 bolt discharge
- T3 .48 or .63 A/R with 5 bolt discharge (with or without wastegate hole)
• 360° journal bearing system

PTE's Entry Level turbochargers help you get the high-end performance you crave in a smaller package at an affordable price.​

 

[turbox-tech]

looks very similar. Mine has the buick 3bolt turbine inlet w/ 5 bolt DP. thnx