Up pipe build advice

[toolguy874.1]

That is your decision.
I used it.
It's over 10 years old with no problems.

V band and flat flange gasket is a pretty precise fit.
Original has a ball socket for misalignment movement.

 

[turbobooster]

That is your decision.
I used it.
It's over 10 years old with no problems.

V band and flat flange gasket is a pretty precise fit.
Original has a ball socket for misalignment movement.

Any pics to share?

 

[toolguy874.1]

Any pics to share?

Just the 3 in post #17.
Not sure what else there is to show.

 

[turbobooster]

Just the 3 in post #17.
Not sure what else there is to show.

Did u rig weld it to the header using SS rod? Did u do any purging when welding your up pipe ? I know it was suggested in an earlier post just wondering how u went about it

 

[WH1]

Here are updated pictures to replace pictures that went missing

Where did you buy the down pipe & did you make the up pipe?

 

[1986 Buick GX1]

Where did you buy the down pipe & did you make the up pipe?

Gbodyparts lists several HA 3” DP packages.

Link below.

GBodyParts.com

 

[WH1]

Thanks!

 

[turbobooster]

Finally getting around to it , mocking up the new 2.5 SS uppipe . It has a slightly different angle , which is shooting down more towards the header compared to stock up pipe what do u guys think ? I still have to add the flex pipe and the other end that goes to the header

 

[turbobooster]

 

[HotAirWH1]

Be conscious of the down pipe flange position where it will bolt to the header & the AC compressor hose where it bolts to the back of the compressor. There is little to no room between the two. I had to grind the "new flange" about a quarter inch & use a flathead machine bolt for the hose to compressor. If you are going to reuse the "old flange" from the old up pipe then you'll probably have a lot more room since its narrower than a "new flange". Curious how your going to marry up the up pipe to the header ball & socket.

 

[turbobooster]

I have completely deleted the a/c system, my plan is to install this aftermarket header utilize the same mating flange on it with the upipe piece u see in the pic once I bolt up the header I will see how much of the header upipe neck needs to be cut away so I can weld the new stainless pipe and flex pipe to the pipe attaching to the turbo, I will be modifying the upipe bolted to the turbo as well and will be using the same flange once measured and cut to size

 

[turbobooster]

Can the 3 bolts coming out of the turbo to up pipe be changed out to new bolts?

 

[HotAirWH1]

I like what you did there !!! Who needs AC anyhow. Just roll down the windows and go fast

Yes. if you change out the studs use a lock nut on the new studs to secure the up pipe. Also you may want to install a
copper gasket.

 

[turbobooster]

What are the springs for and where do they go ? I remember having them on an old uppipe I use to have but I don’t have those anymore are they needed?

 

[HotAirWH1]

The attachments are for a stock down pipe (which you are not using). I accidently attached them when posting. Please disregard.

 

[turbobooster]

What about the bolts Will those work as replacements? Or is there a different part number ?

 

[HotAirWH1]

Different part. You could go with a lock nut & bolt.

The Stock assembly is:
Black-Oxide Steel Threaded on Both End Stud M10 x 1.5 mm Thread, 20 mm Thread Lengths, 50 mm Long
and a High-Strength Steel Distorted-Thread Flange Locknut Class 10, Black-Oxide, M10 x 1.5 mm Thread




Your not using the Up Pipe to Turbo Adapter

 

[turbobooster]

Where did u get those from ?

 

[HotAirWH1]

Where did u get those from ?

Links below:

McMasters - Carr

SCE Gasket