Recent content by V SICKS

  1. V

    Difference in high and low inpedence injectors?

    Would someone shed some light on the high and low impedence injectors. Which ones are best and which are not so good? THANKS..mike
  2. V

    Is there any aftermarket turbo that will bolt to an 85 GN throttlebody?

    Can you post photo.. I am getting lost. THANKS..mike
  3. V

    ARP rod bolts with rods already resized?

    I can put a new set of OEM bolts in and be 100% safe, and right on the money size wise. How many turbo guys have broken a rod bolt?? Not very many I bet. I'm trying to find out if anyone actually did put in a set of ARP's with out resizing and had no problems? THANKS for the input and lets hear...
  4. V

    ARP rod bolts with rods already resized?

    I went ahead and resized my rods a few months ago while I had access to the equipment with stock bolt with the though of using ARP when I put them in the engine. ARP says to always resize the rods. New stock bolts from TA are like $6 each, same as a set of ARP. I don't know the history of the...
  5. V

    Is there any aftermarket turbo that will bolt to an 85 GN throttlebody?

    I will be watching for your input. As I said I am in the middle of a hot air rebuild and don't want to make $800 mistakes. My money tree is also a little bare...I also posted my turbo spec tag in the turbo section for help..THANKS..mike
  6. V

    Please read my post in the turbo section.

    Not a lot of traffic over there. Its the Please help with rebuild tag decode. THANKS... mike
  7. V

    Help decode rebuild tag on hot air please

    Took my turbo out of the housing.. Tag says: FACTORY OVERHAULED TURBOCHARGER S/N RKR01010 10 10 PN 466122-9001 Air Research Industrial Division Does the 10 10 on the end of the first line indicate boring the housing .010 like a crankshaft? Do you suppose the wheels might be...
  8. V

    Is there any aftermarket turbo that will bolt to an 85 GN throttlebody?

    Is the TA33 easier and cheaper to do than the TA49 or the other way around? I also am building a hot air and want to upgrade but its a lot of money. THANKS...mike
  9. V

    What color is your engine painted?

    While I have the engine out or my 84 T which is light tan, what other color besides black would look good on the engine? There has got to be some of you that didn't paint yours black? THANKS... mike
  10. V

    Posi carrier parts?

    No photo but it is the one with the "S" spring in the middle on the spider gear shaft. There is definitely no gov in there. Housing is a 410408. The clutches may be OK but I am not sure from looking at them. I would rather only do it once... THANKS...mike
  11. V

    Posi carrier parts?

    I bought a posi carrier to put in my 84T while I am going through engine. I think its a Eaton? It is suppose to be the factory set up. What I want to know is where to buy the clutch pack? I figure its best to replace them before I put it in the car. Please don't tell me not to use it and buy...
  12. V

    Turbo engine balance?

    Is the 231 turbo engine considered to be internal or external balance? THANKS...mike
  13. V

    Please help with my post in wheel section

    Please read my post in the wheels section on fixing 84 T-Type wheels. I am not getting any help and very little traffic in that section.. THANKS.. mike aka- V SICKS
  14. V

    How to re-do 84 T-type wheels?

    While cleaning up my wheels I see bright and hazy areas on the machined fins or vanes or what every you call them. How can I polish the machined areas and then replace the clear coat with what? Is there a simple method to polish the aluminum these wheels are made of? Area between vanes appears...
  15. V

    More head and a pan gasket to trade?

    Come on guys... whats the difference in the 8723 like came in my FelPro gasket set for my 84 and the 9441 everyone is talking about...the 8723 doesn't look like multi layer but looks like it would work in a turbo car?? THANKS.. mike
See more
Top