Billet Roller Cam stuff, 3.5" Exhaust

[jpwalt1987]

224/224@.050 .560/.560lift with1.6 rocker .010 lash
Billet Solid Roller cam

It is setup for a 109 block and has the odd-fire style nose assembly.

Cam only -$ 300

Crane sheilded foot solid roller lifters-2000 miles- $250

DLS pushrods for the above setup 9.050 5/16ths $100

This cam pulls hard to 6500rpm and I spooled a pt70 with 231 cid engine and 3200rpm convertor quick enough to have a traction problem with D/Rs. The idle was pretty good also.

No reasonable offer will be refused:smile:

I have a 3.5 inch exhaust system that I built using madrel bent tubing pieces. It has a center in/center out Hooker Aerochamber muffler. I just had it sandblasted and then I coated it with cold galvanizing spray and VHT flame proof silver paint. This will clear a 3 in driveshaft and stock contol arms. It is set up to come directly off of the downpipe but could be trimmed to meet a cut out pipe. You will need 2 band clamps for the connections. I believe I have one to go with it though. (have to check.)

Would like to get $350 shipped.

Thanks for looking. Jeremy

 

[Cme2fly]

224/224@.050 .560/.560lift with1.6 rocker .010 lash
Billet Solid Roller cam

It is setup for a 109 block and has the odd-fire style nose assembly.

Cam only -$ 300

Crane sheilded foot solid roller lifters-2000 miles- $250

DLS pushrods for the above setup 9.050 5/16ths $100

This cam pulls hard to 6500rpm and I spooled a pt70 with 231 cid engine and 3200rpm convertor quick enough to have a traction problem with D/Rs. The idle was pretty good also.

No reasonable offer will be refused:smile:

Pm sent on the lifters.thanks

 

[jpwalt1987]

Sale pending on the roller lifters to CME2FLY

 

[Jay Wicks]

Interested. Could I get a picture of the cam nose please? Thank You.

 

[jpwalt1987]

100_1198 pictures from cars photos on webshots

Here is a pic of it all put together. I still have to pull the cam out of my engine. THe engine is on the stand right now, but I have a wedding today and mothers day tomorrow, so it will be Monday before I can do that. I will do that as soon as possible though.

 

[boostingirl]

how many miles on this cam?

 

[jpwalt1987]

how many miles on this cam?

maybe 2000

 

[bison]

how many miles on this cam?

why would that matter?

 

[jpwalt1987]

Here you go, Jay.

 

[jpwalt1987]

Cam and Pushrods back up for sale. Roller lifters sold to CME2FLY

Cam only(no front hardware) $275 shipped

Pushrods $75 shipped

Gotta move this stuff.

 

[norbs]

If you want to see this cam idle and see how it sounds to you please check out the post below. I have great vacuum too, but i keep the idle a bit higher to keep the oil psi up.

http://www.turbobuick.com/forums/computer-chips-101/319552-tt-95-6-0-chip-testing-video.html#post2508463

 

[jpwalt1987]

BUMP for cam and pushrods

 

[bdasv6]

cam

pm sent

 

[87action]

exhaust

This is nice, bump for a nice system. By the way where did your roller cam come from? Weber, T/A, DLS?

 

[jpwalt1987]

the cam is a DLS setup from when he was at PTE

 

[KevinB]

Is the exhaust still for sale? Its aluminized, right?

 

[jpwalt1987]

Is the exhaust still for sale? Its aluminized, right?

When I built it years ago the shop sold me some pieces that were aluminized and some that were bare. The bare had some rust on it so I had the whole thing sandblasted last week and then I coated it with cold galvanizing spray and VHT high temp paint. It is still for sale. I have a hanger that I made to go behind the muffler that I forgot to take a picture of also. Hope this helps.

 

[KevinB]

When I built it years ago the shop sold me some pieces that were aluminized and some that were bare. The bare had some rust on it so I had the whole thing sandblasted last week and then I coated it with cold galvanizing spray and VHT high temp paint. It is still for sale. I have a hanger that I made to go behind the muffler that I forgot to take a picture of also. Hope this helps.

Do you think it will fit hr suspension and bar?

 

[jpwalt1987]

Do you think it will fit hr suspension and bar?

By looking at pics of the HR bar.... if it didnt fit, it wouldnt be by much. I am not sure. There are some pics in my webshots link that show the exhaust when I first built it. I am not sure where the HR bar mounts but that should give you a better idea. The hangers in the webshots pics have been revised also. The tailpipe section can be rotated a little to gain clearance. Jeremy

 

[jpwalt1987]

new prices

Cam $225 plus shipping

Exhaust $225 plus shipping