Where does this go?

[jimski]

what is this and where does it go?

 

[jimski]

Please help a poor guy out in over his head

 

[blackazz]

Where did you find it.

 

[6cylboost]

Give me a hint. transmission?

 

[buddy]

It's a penis ring. It goes around your penis.

 

[Steve V]

My guess is under the low planet in the bottom end. My book is outside if no one posts for sure I will grab it and look in the am.

 

[jimski]

Where did you find it.

It came in the alto rebuild kit. when i took 2004r bq unit apart this crap was not in there. atsg and it is vague. figure some one here will help me stop second guessing

 

[jimski]

My guess is under the low planet in the bottom end. My book is outside if no one posts for sure I will grab it and look in the am.

please check for me, i hope this crap does not go low in there. The low part is all snapped in there allready. when i took the 2004r bq apart this was not in there.

 

[jimski]

It's a penis ring. It goes around your penis.

if it is, wont do me no good wit my 2" er

 

[jimski]

Give me a hint. transmission?

2004r it came in the alto rebuild kit. when i took the unit apart this ring was not in there.

 

[David Husek]

It goes in the garbage in short. Not sure why they still put them in kits. It goes in the rear planetary below the sprag. It should always be updated to a roller bearing as your BQ will already have.

 

[bison]

what is this and where does it go?

It's a thrust washer. In the trash bin


Sent from my iPhone using Tapatalk

 

[jimski]

It goes in the garbage in short. Not sure why they still put them in kits. It goes in the rear planetary below the sprag. It should always be updated to a roller bearing as your BQ will already have.

thanks

 

[jimski]

It's a thrust washer. In the trash bin


Sent from my iPhone using Tapatalk

thanks for the reply, i am filing it now.

 

[jimski]

It goes in the garbage in short. Not sure why they still put them in kits. It goes in the rear planetary below the sprag. It should always be updated to a roller bearing as your BQ will already have.

I hate to be s pain here but is there a picture somewhere showing the rollerized part, does it go under the gear that goes into the lo sprag? Just trying to be sure I allready snapped the lower portion of the trans in and do not want to go further till I'm sure. If I remember correctly the round gear that goes into the sprag with grooved side down did not have and needle bearing in there. It just sat in there.

 

[INEEDAGN]

You can see it under the sprag in this photo. This one has a plastic washer but you see where the bearing should go. You probably never had yours apart far enough to forget the bearing.

 

[jimski]

You can see it under the sprag in this photo. This one has a plastic washer but you see where the bearing should go. You probably never had yours apart far enough to forget the bearing.
View attachment 266615

True I did not take it apart far enough. Bq trans so it may be updated thanks for the pick. I thought it went under the center gear with the groove side down

 

[TexasT]

http://www.ihadav8.com/forum/index.php?topic=3729.0
Here is a pic I took when mine was apart.

It is in reply number seven. I'm on my phone or I'd put up a pic.

 

[jimski]

http://www.ihadav8.com/forum/index.php?topic=3729.0
Here is a pic I took when mine was apart.

It is in reply number seven. I'm on my phone or I'd put up a pic.

I pulled everything back out just to confirm this is a rollerized planet. Thanks to all for helping me out.

 

[jimski]

There was nothing inside this planet gear. The guy I paid to rebuild the trans must have forgot to put the roller bearing back in it. This is why I'm rebuilding the bq3 myself.